AVSPARE.COM
parts catalog

HARNESS AS 1247423 - Caterpillar



1247423 HARNESS AS Caterpillar parts D6E, D6G SR HARNESS
Rating:
17
Alternative (cross code) number:
CA1247423
124-7423
1247423
Caterpillar 1247423 HARNESS AS
Weight: 0.70 pounds 0 kg.

Buy HARNESS AS 1247423 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 1247423:

TRACK-TYPE TRACTOR  D6E   D6G SR   Caterpillar
Number on catalog scheme: 64
 
  For full view, you need register

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
3216-11
Aftertreatment #1 Intake NOx : Other Failure Mode 3655-11
Aftertreatment #1 Intake NOx Level Sensor : Other Failure Mode The intake NOx sensor heater cannot generate enough heat or the power supply is intermittent.
3216-12
Aftertreatment #1 Intake NOx : Failure 3655-12
Aftertreatment #1 Intake NOx Level Sensor : Failure A failed intake NOx sensor has been detected.
3226-11
Aftertreatment #1 Outlet NOx : Other Failure Mode 3609-11
Aftertreatment #1 Outlet #1 NOx Level Sensor : Other Failure Mode The outlet NOx sensor heater cannot generate enough heat or the power supply is intermittent.
3226-12
Aftertreatment #1 Outlet NOx : Failure 3609-12
Aftertreatment #1 Outlet #1 NOx Level Sensor : Failure A failed outlet NOx sensor has been detected. Note: Turn the keyswitch to the OFF position before connecting or disconnecting these components.If the Cat® Electronic Technician (ET) will not communicate with the Electronic Control Module (ECM), refer to Troubleshooting, "Electronic Service Tool Does Not Communicate" before you begin this procedure. The procedure verifies that electrical power is being supplied to the ECM and to the service tool connector.The data links are used to communicate information between the engine ECM and other control modules that are a part of the application. Cat ET also communicates with the ECM via the data links.The service tool connector contains connections for electrical power and for the data links.When the keyswitch is in the OFF position, Cat ET may communicate with the ECM. However, the communications may be disrupted and the communications may require frequent reconnection. To avoid this problem, place the keyswitch in the ON position when Cat ET is being used.Cat ET may display the following error message:"The version of the ECM is not recognized and the integrity of the changed parameters and displayed data is not guaranteed."This message indicates that one of the following conditions exist:
The flash file in the ECM is newer than the version of Cat ET.
The latest version of Cat ET has not been installed.
Illustration 1 g06086930
Table 2
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect the connectors. Refer to Troubleshooting, "Electrical Connectors-Inspect" for additional information.
C. Perform a 45 N (10 lb) pull test on the connector wires.
D. Check the harness for abrasions and pinch points.
Connectors and Wiring
Result: The connectors and wiring appear to be OK.
Repair: If a -12 code is active or logged, replace the appropriate NOx sensor. Refer to Special Instruction, REHS8151 for special handling instructions.
Proceed to Test Step 3.
If a -11 code is active or logged, proceed to Test Step 2.
Result: There is a problem with the connectors and/or wiring.
Repair: Repair or replace the connectors or wiring. Ensure that all the seals are properly in place and ensure that the connectors are coupled.
If the problem is not resolved, proceed to Test Step 2.
2. Check the Voltage to the Affected Sensor
A. Disconnect the affected sensor from the wiring harness.
B. Turn the keyswitch to the ON position.
C. Measure the voltage on the wiring

Caterpillar parts catalog:

Caterpillar parts catalog
D6G Track-Type Tractor Super Rural 3SR00001-UP (MACHINE) POWERED BY 3306 Engine
D6G Track-Type Tractor Power Shift 2MJ02654-UP (MACHINE) POWERED BY 3306 Engine


Parts harness Caterpillar catalog:

9G6119 HARNESS AS
561D, D5B, D5E, D6D, D6E, D6E SR
9G6120 HARNESS AS
561D, D5B, D5E, D6D, D6E, D6E SR
9P3118 HARNESS AS
561D, D4E, D4E SR, D5B, D5E, D6D, D6E, D6E SR
2Y5405 HARNESS AS
D4E, D4E SR, D5E, D6D, D6E, D6E SR
1245673 HARNESS AS
D6E, D6F SR, D6G SR
1246460 HARNESS AS
D6E, D6F SR, D6G SR
1127686 HARNESS AS-SWITCH
D10R, D11R, D5M, D6M, D6R, D7R
1246460 HARNESS AS
D6E, D6F SR, D6G SR
1245673 HARNESS AS
D6E, D6F SR, D6G SR
1279599 HARNESS AS
D6E, D6F SR, D6G, D6G SR
1246354 HARNESS AS
D6E, D6F SR, D6G SR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.