AVSPARE.COM
parts catalog

HARNESS AS-CHASSIS 3599014 - Caterpillar



3599014 HARNESS AS-CHASSIS Caterpillar parts 793F, 793F-XQ HARNESS
Rating:
11
Alternative (cross code) number:
CA3599014
359-9014
3599014
Caterpillar 3599014 HARNESS AS-CHASSIS
Weight: 12 pounds 5 kg.

Buy HARNESS AS-CHASSIS 3599014 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compatible equipment models: 3599014:

TRUCK  793F   793F XQ   Caterpillar
Number on catalog scheme: 25
 
  For full view, you need register

Information:

Pump Destroke Pressure
Destroking pressure is the control pressure from the pump control to the pump destroke servo.Note: Each implement piston pump must be isolated and checked separately. Disconnect the power shift signal pressure from the pumps which are not being checked.
Install a 40000 kPa (5800 psi) pressure gauge and test hose onto pressure tap (6) in order to measure the discharge pressure of the implement piston pump.
Illustration 6 g00800065
Regulator control valve for the implement piston pump (8) Relief valve for bucket curl function
Reduce the pressure setting of the relief valve (8) by turning the adjuster counterclockwise by 5 turns.Note: Do not turn the adjuster more than 5 turns. Removal of adjuster out of the valve may result in loss of oil.Note: Each implement piston pump must be isolated and checked separately. Full pump flow through the line relief valve may damage the valve.
Isolate one implement piston pump by disconnecting the power shift signal from all the implement piston pumps which are not being checked. Refer to "Pump Isolation".
Illustration 7 g00771449
Implement piston pump (9) "M1" port
Install 6V-3965 Fitting As into six "M1" ports (9) for the implement pumps. Install a 6V-7830 Tetragauge and a test hose onto the fitting assembly at the "M1" port of the pump that is being tested.
Illustration 8 g00662188
Connection for power shift signal
Install a 4000 kPa (580 psi) pressure gauge and test hose into the power shift system on the pump in order to measure the pressure of the power shift signal.
Start the engine.
Warm the oil to a minimum temperature of 50 °C (122 °F). Refer to the Testing and Adjusting, "General Information" for the proper procedure for warming the hydraulic oil.
Set the throttle switch to position 1.
Illustration 9 g00465069
The electronic service tool that is connected to the diagnostic connector for ET that is located in the cab
Illustration 10 g00465070
The electronic service tool that is connected to the diagnostic connector for ET that is located in the pump room
Set the power shift pressure to a constant 1380 kPa (200 psi) by using the Electronic Technician Software and the M300 Technician software. Connect the Electronic Service Tool with a 7X-1700 Communication Adapter to the diagnostic connector for ET with a 7X-1425 cable and a 7X-1570 cable. Either the diagnostic connector for ET that is located in the cab or located in the pump room may be used. Use the override parameters in order to set the power shift pressure.
Slowly actuate the bucket curl function to the open position. Hold the open position for the bucket curl function in a stalled condition. Read the pressure for the power shift signal, for the "M1" port pressure, and for

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
793F Off-Highway Truck SSP00001-UP (MACHINE) POWERED BY C175-16 Engine
793F XQ Off-Highway Truck SND00001-UP (MACHINE) POWERED BY C175-16 Engine


Parts harness Caterpillar catalog:

3586266 HARNESS AS-WIRING
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797F
3791768 HARNESS AS-CHASSIS
793F, 793F CMD, 793F OEM
1927805 HARNESS AS-VALVE
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24H, 24M, 416E, 422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 44...
1664341 HARNESS AS-WIRING
793F, 793F AC, 793F CMD, 793F OEM, 795F AC, 797, 797B, 797F
3633246 HARNESS AS-SENSOR
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F
3791021 HARNESS AS-PANEL
793F, 793F AC, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.