AVSPARE.COM
parts catalog

HARNESS AS-WIRING 3599625 - Caterpillar



3599625 HARNESS AS-WIRING Caterpillar parts CG137-08, CG137-12 HARNESS
Rating:
49
Alternative (cross code) number:
CA3599625
359-9625
3599625
Caterpillar 3599625 HARNESS AS-WIRING
Weight: 23 pounds 10 kg.

Buy HARNESS AS-WIRING 3599625 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: 3599625:

GAS ENGINE  CG137-08   CG137-12   Caterpillar
  For full view, you need register

Information:

Ejector Kickout Valve
The ejector kickout valve is in the end of the valve stem for the ejector (in the control valve).
REAR OF SCRAPER CONTROL VALVE (Typical)
1. Housing. 2. Valve. 3. Air line.To check the pressure setting of the kickout valve, use the test equipment installed in the pump connection that was used in the test for the relief valve in the control valve.With the engine running at high idle rpm and the floor OPEN, move the control lever for the ejector to the return (detent) position. Look at the pressure gauge when the floor closes. When the pressure reading on the gauge is 1900 100 psi (13 090 690 kPa), the ejector kickout valve must open to move the control lever for the ejector to the HOLD position.If it is necessary to change the pressure setting of the ejector kickout valve, disconnect oil line (3) from valve (2) on the end of spring housing (1) for the ejector valve stem and remove the valve.
KICKOUT VALVE IN EJECTOR VALVE STEM
1. Spring housing. 4. Screw.Use a .12 inch hex wrench through the hole in the end of spring housing (1), where the air valve was removed, and turn the screw either clockwise to increase or counterclockwise to decrease the pressure setting of the ejector kickout valve. One-half turn of screw (4) changes the pressure setting of the valve approximately 135 psi (930 kpa).If air valve (2) on the end of housing (1) was removed, the torque to install the valve is 55 5 lb. ft. (75 7 N m). Connect air line (3) to valve (2).Elevator Chain Adjustment
Hydraulic chain adjusters, one on each side of the elevator frame, are used when it is necessary to remove excess slack from the elevator chains. Open the covers, on the frame, over the grease fitting on the hydraulic chain adjusters.Use a grease gun to put grease in the adjusters at fitting (1). Do not loosen the clamps on the yokes. The correct slack is 5 to 8 in. (127.0 to 203.2 mm) measured between the chains and the lower guide rollers. The distance between the lower idler and the sprocket on each side of the elevator frame must be the same.If the chain adjusters are near maximum extension, retract the adjusters and remove two links from each chain. Install one offset link. Loosen fitting (1) one turn to retract adjuster.
MEASURING CHAIN ADJUSTMENT
Do not loosen either the fitting or the bleed valve more than one turn when it is necessary to retract the hydraulic adjusters.
HYDRAULIC CHAIN ADJUSTER
1. Fitting.Testing And Charging The Accumulator
7S5437 Nitrogen Charging Group.Be sure the elevator has been stopped for a minimum of five minutes. This is enough time to let the piston push the oil out of the accumulator. The piston must be on the bottom of the cylinder to be sure that the pressure of the nitrogen charge is correct.The accumulator (1), in an oil line to the elevator hydraulic motor, has a charge of approximately

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts harness Caterpillar catalog:

2701732 HARNESS AS-CONTROL
3176B, 3176C, 3196, 3406E, 3412, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 3516C, C175-16, CG137-12, G3406, G3408, G3408C, G3412, G3508, G3508B, G3512, G3512B, G3512E, G3516, G3516B, G3516C, G351...
2760785 HARNESS AS-CONTROL
3176B, 3176C, 3196, 3406E, 3412, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C175-16, C18, CG137-12, G3406, G3408C, G3412, G3508, G3508B, G3512, G3512B, G3512E, G3516, G3516B, G3516C, ...
1940895 HARNESS AS-PANEL
CG137-12, G3408C, G3412, G3508, G3512, G3516
1018641 HARNESS AS-WIRING (NOTE H)
426B, 436B, CG137-12, G3412
2400221 HARNESS AS-ENGINE
CG137-12, G3408, G3408C, G3412, G3412C
1046727 HARNESS AS-TRANSMISSION
950F, 950F II, 960F, 966F, 966F II, 970F, 980F, 980F II, 988F, 988F II, R1300, R1300G, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
1523825 HARNESS ASSEMBLY
950G, 962G, 966G, 972G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.