AVSPARE.COM
parts catalog

HARNESS AS-SENSOR 3599725 - Caterpillar



3599725 HARNESS AS-SENSOR Caterpillar parts 797F HARNESS
Rating:
20
Alternative (cross code) number:
CA3599725
359-9725
3599725
Caterpillar 3599725 HARNESS AS-SENSOR
Weight: 1 pounds 0 kg.

Buy HARNESS AS-SENSOR 3599725 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compatible equipment models: 3599725:

TRUCK  797F   Caterpillar
Number on catalog scheme: 10
 
  For full view, you need register

Information:

Note: The surface of the seal outside diameter and the counterbore in the equalizer bar should be clean, dry, free from grease, oil, and loosely adhering contaminants. Never clean the surfaces with gasoline, naphtha, or other solvents which leave a film after drying.
Make sure that the sealing surfaces of the seals and of the equalizer bar are smooth and clean.
Use Tooling (A) to install one retaining ring in the end of the equalizer bar.
Illustration 1 g00556809
Use Tooling (B) to install the bearing for the equalizer bar end pin. Press the bearing until the bearing makes contact with the retaining ring. The bearing must be started square with the bore before pressure is applied with Tooling (B) .
Illustration 2 g00526380
Install retaining ring (5) in the equalizer bar.
Illustration 3 g00556867
Illustration 4 g00526376
Note: The surface of the seal outside diameter and the counterbore in the equalizer bar should be clean, dry, free from grease, oil, and loosely adhering contaminants. Never clean the surfaces with gasoline, naphtha, or other solvents which leave a film after drying.
After cleaning the surfaces, apply Tooling (E) on either the metal surface of seals (4) or the mating surface. Tooling (E) will leave behind a catalyst. This will decrease the amount of time that is needed for the sealant to cure. For faster curing, Tooling (E) can be applied to both surfaces. Allow one to two minutes for Tooling (E) to dry prior to applying Tooling (D) . The maximum storage life of Tooling (E) is 12 months.Note: Assemble seals (4) with the part number toward the outside of the equalizer bar.
After Tooling (E) is dry, apply Tooling (D) to the outside surface of seals (4) . Use Tooling (C) to install seals (5) in the equalizer bar.Note: Assemble the seals with the part number toward the outside of the equalizer bar.
Repeat steps 2 through 7 for the other end of the equalizer bar.
Illustration 5 g00526374
Put center bearing (2) in position. Start center bearing (2) square in the equalizer bar.
Install two bearings (2) . Install the bearings level to the front surface of the equalizer bar.
Illustration 6 g00526371
Note: The surface of the seal outside diameter and the counterbore in the equalizer bar should be clean, dry, free from grease, oil, and loosely adhering contaminants. Never clean the surfaces with gasoline, naphtha, or other solvents which leave a film after drying.
After cleaning the surfaces, apply Tooling (E) on either the metal surface of seals (1) or the mating surface. Tooling (E) will leave behind a catalyst. This will decrease the amount of time that is needed for the sealant to cure. For faster curing, Tooling (E) can be applied to both surfaces. Allow one to two minutes for Tooling (E) to dry prior to applying Tooling (D) . The maximum storage life of Tooling (E) is 12 months.Note: The seals for the center pin are different sizes. Make sure that the seals are installed in the correct bores.
Apply Tooling (D) to the outside surface of seals (1) . Use Tooling (C) to install seals

Caterpillar parts catalog:

Caterpillar parts catalog
797F Off-Highway Truck LAJ00001-UP (MACHINE) POWERED BY C175-20 Engine
797F XQ Off-Highway Truck WSP00001-UP (MACHINE) POWERED BY C175-20 Engine


Parts harness Caterpillar catalog:

3761303 HARNESS AS-ENGINE
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797F
3653535 HARNESS AS-SWITCH
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD, 770, 772, 773F, 775F, 777F, 789D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797F, 834K, 836K, 844K, 924K, 930K, 938K, 988K...
3601914 HARNESS AS-SENSOR
785C, 785D, 789C, 793D, 793F, 797F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.