AVSPARE.COM
parts catalog

HARNESS AS-ENGINE 3599896 - Caterpillar



3599896 HARNESS AS-ENGINE Caterpillar parts 627H, 725C HARNESS
Rating:
9
Alternative (cross code) number:
CA3599896
359-9896
3599896
Caterpillar 3599896 HARNESS AS-ENGINE
Weight: 7 pounds 3 kg.

Buy HARNESS AS-ENGINE 3599896 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK, WHEEL TRACTOR,

Compatible equipment models: 3599896:

ARTICULATED TRUCK  725C  
WHEEL TRACTOR  627H   Caterpillar
Number on catalog scheme: 3
 
  For full view, you need register

Information:

Face Runout (Axial Eccentricity) of the Flywheel
Table 1
Tools Needed    
Part Number     Part Name     Quantity    
8T-5096     Dial Indicator Gp     1    
Illustration 1 g02509960
Checking face runout of the flywheel
Refer to Illustration 1 and install the dial indicator. Always put a force on the crankshaft in the same direction before the dial indicator is read. to remove any crankshaft end clearance.
Set the dial indicator to read 0.0 mm (0.00 inch).
Turn the flywheel at intervals of 90 degrees and read the dial indicator.
Take the measurements at all four points. The difference between the lower measurements and the higher measurements that are performed at all four points must not be more than 0.13 mm (0.005 inch) runout per 25.4 mm (1.0 inch) of the diameter of the flywheel.Bore Runout (Radial Eccentricity) of the Flywheel
Table 2
Tools Needed    
Part Number     Part Name     Quantity    
7H-1942     Dial Indicator     1    
Illustration 2 g02509996
Checking bore runout of the flywheel (1) 7H-1945 Holding Rod (2) 7H-1645 Holding Rod (3) 7H-1942 Dial Indicator (4) 7H-1940 Universal Attachment
Install 7H-1942 Dial Indicator (3) . Make an adjustment of 7H-1940 Universal Attachment (4) so the dial indicator makes contact on the flywheel.
Set the dial indicator to read 0.0 mm (0.00 inch).
Turn the flywheel at intervals of 90 degrees and read the dial indicator.
Take the measurements at all four points. The difference between the lower measurements and the higher measurements that are performed at all four points must not be more than the following values for the maximum permissible face runout (radial eccentricity) of the flywheel.Flywheel ... 0.13 mm (0.005 inch)
Illustration 3 g02510080
Flywheel clutch pilot bearing bore
To find the runout (eccentricity) of the pilot bearing bore, use the preceding procedure.
The runout (eccentricity) of the bore for the pilot bearing in the flywheel must not exceed the following values:Flywheel ... 0.13 mm (0.005 inch)

Caterpillar parts catalog:

Caterpillar parts catalog
725C2 Articulated Truck 2L600001-UP (MACHINE) POWERED BY C9.3 Engine
725C Articulated Truck LFB00001-UP (MACHINE) POWERED BY C9.3 Engine
627H Wheel Tractor Scraper LCT00001-UP (MACHINE)


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.