AVSPARE.COM
parts catalog

HARNESS AS 9V9619 - Caterpillar



9V9619 HARNESS AS Caterpillar parts 916 HARNESS
Rating:
15
Alternative (cross code) number:
CA9V9619
9V-9619
9V9619
Caterpillar 9V9619 HARNESS AS
Weight: 2 pounds 0 kg.

Buy HARNESS AS 9V9619 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 9V9619:

WHEEL LOADER  916   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2269 Ridge Reamer 1 Start By:
Remove the oil suction pipe. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
If necessary, remove the balancer. Refer to Disassembly and Assembly, "Balancer - Remove" for the correct procedure.
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Rotate crankshaft until the required connecting rod is at bottom dead center.
Using tooling (A), remove carbon build-up from the top of the cylinder bore.
Illustration 1 g03001196
Typical example
Note: Do not stamp the connecting rod assembly. Stamping or punching the connecting rod assembly could cause the connecting rod to fracture.
The connecting rod and the connecting rod cap should have an etched number in Position (X). The number on the connecting rod and the connecting rod cap must match. Ensure that connecting rod (3) and connecting rod cap (1) are marked for the correct location. If necessary, make a temporary mark on the connecting rod and the connecting rod cap in order to identify the cylinder number and orientation of the assembly.
Remove the bolts (2) and remove connecting rod cap (1) from connecting rod (3).
Rotate crankshaft so that the required piston is at top center position.
Illustration 2 g02998516
Typical example
Carefully push piston (4) and the connecting rod out of the cylinder bore. Lift piston (4) out of the top of the cylinder block. Note: Do not apply force to the fracture split surfaces of the connecting rod as damage may result.
Temporarily install connecting rod cap (1) and bolts (2) to connecting rod (3) when the assembly is out of the engine. Ensure that the etched number on connecting rod cap matches the etched number on connecting rod. Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side. Tighten bolts (2) to a torque of 20 N m (177 lb in).
Repeat Step 1 through Step 7 in order to remove the remaining pistons and connecting rods. Fracture split connecting rods should not be left without the connecting rod caps installed.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
916 WHEEL LOADER 2XB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
G916 WHEEL LOADER 5GD00001-00047 (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 2XB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 5KC00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 5KC01849-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 5KC00001-UP (MACHINE) POWERED BY 3204 ENGINE


Parts harness Caterpillar catalog:

8V7858 HARNESS AS
916, 926A, 936, CS-643, IT18, IT18B, IT28, IT28B
9V3734 HARNESS AS
916, 926A, 936, IT28
1506999 HARNESS AS-CONSOLE
320B, 320B U, 322B, 322B L, 325B, 325B L, 330B, 330B L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.