AVSPARE.COM
parts catalog

HARNESS A 9V9859 - Caterpillar



9V9859 HARNESS A Caterpillar parts HARNESS
Rating:
36
Alternative (cross code) number:
CA9V9859
9V-9859
9V9859
Caterpillar 9V9859 HARNESS A
Weight: 2 pounds 1 kg.

Buy HARNESS A 9V9859 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

1. Drain the coolant from the cooling system. 2. Loosen the clamps that hold hose (3) to the regulator housing. Move the hose away from the regulator housing.3. Remove bolts (1) and move tube (2) away from the housing.4. Disconnect two tube assemblies (4) from the regulator housing. 5. Disconnect the wires from switches (7), (8) and (10).6. Remove the bolt and clamp that holds wire harness (9) to the regulator housing.7. Remove the bolts and retainers that hold tube (5) in place in the regulator housing and water pump. Remove the tube.8. Fasten a hoist and tool (A) to regulator housing (6). Remove bolts (11) and the bolts that hold the regulator housings to the bracket. Remove the regulator housings from the engine. The weight of the regulator housings is 37 kg (81 lb). 9. Put the regulator housing in the position shown. Remove bolts (12), and separate the regulator housings. 10. Remove water temperature regulators (13) from the regulator housing. 11. Remove seals (14) and ferrule (15) from the regulator housing. Remove the ball from under ferrule (15). The following steps are for installation of the water temperature regulators. 12. Install the ball and ferrule (15) in the regulator housing. Make sure the open end of the ferrule is toward the outside of the housing. Ferrule (15) must make contact with the bottom of the bore.13. Install new seals in the housing with tool (B). Install the seals with the lip toward the inside of the regulator housing.
If the water temperature regulators are installed wrong, it will cause the engine to overheat.
14. Install water temperature regulators (13) in the regulator housing with the spring up as shown.15. Fasten a hoist and tool (A) to the housing. Put the gasket and housing in position on regulator housing (6), and install the bolts that hold them in place.16. Fasten a hoist and tooling (A) to regulator housing (6). Put the regulator housing and the gaskets in position, and install bolts (11) and the bolts that hold the regulator housings to the brackets.17. Install the clamps and bolts that hold tube assembly (5) to the regulator housing.18. Connect the 441 OR wire to switch (8).19. Connect the 200 BK and 311 WH wires to switch (7).20. Connect the 406 PU and 438 YL wires to switch (10).21. Make sure the O-ring seals are in position on each end of tube (5). Put clean oil on the O-ring seals. Put tube (5) in position in the water pump and regulator housing. Install the retainers and bolts to hold it in place.22. Install the clamp and bolt that holds wire harness (9) to the regulator housing.23. Connect two tube assemblies (4) to the regulator housing.24. Connect hose assembly (3).25. Put tube (2) in position on the regulator housing and install clamps and bolts (1) to hold it in place.26. Fill the cooling system with coolant to the correct level. See the Maintenance Manual.


Parts harness Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.