AVSPARE.COM
parts catalog

HOOD & GUARD GP 1246343 - Caterpillar



1246343 HOOD & GUARD GP Caterpillar parts 980G HOOD
Rating:
50
Alternative (cross code) number:
CA1246343
124-6343
1246343
Caterpillar 1246343 HOOD & GUARD GP

Buy HOOD & GUARD GP 1246343 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 1246343:

WHEEL LOADER  980G   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

oil return tube. 6. Loosen the hose clamps (10) and disconnect the air inlet hose. Install lifting sling (9), remove four bolts (11) and remove turbocharger (8). The weight of the turbocharger is approximately 36 kg (80 lb). The following steps are for installation of the turbocharger.7. Make sure the studs are tightened in the exhaust manifold assembly to a torque of 25 4 N m (20 3 lb ft).8. Install the gasket on the exhaust manifold assembly.9. Fasten a suitable lifting device and put the turbocharger in position. Put 5P-3931 Anti-Seize Compoundon the threads of the studs and nuts (11). Install the nuts and tighten them to a torque of 54 5.5 N m (40 4.00 lb ft).10. If necessary, make a replacement of the O-ring seals on elbow (2) and put clean engine oil on them. Put 4C-5598 Anti-Seize Compound on the threads of the bolts that hold elbow (2) to the inlet manifold. Install elbow (2).11. Install the air inlet hose and tighten clamps (10). Position oil return tube and install bolts (7). Connect two tubes (6) and line (5). Install two hoses (3) and (4). For more detailed information regarding the turbocharger, see the topic "Turbocharger" in the Specifications Manual.12. Fill the cooling system with coolant to the correct level. Refer to the Operation & Maintenance Manual for this procedure.Disassemble & Assemble Turbocharger
Start By:a. remove turbocharger FLUID SPILLAGE CONTAINMENT Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Install turbocharger in Tool Group (A). Put marks on the three housings of the turbocharger for correct installation and alignment at assembly. Loosen "V" clamp (2) and remove compressor housing (1).2. Loosen "V" clamp (3). Remove cartridge housing (4) from turbine housing (5). 3. Put the cartridge assembly in Tool (B) as shown.
do not put a side force on the shaft.
4. Use Tool (C) and remove the nut that holds compressor wheel (6). Remove compressor wheel (6). 5. Remove turbine shaft (7) from the cartridge housing. 6. Remove seal ring (9) and shroud (8) from turbine shaft (7). 7. Use Tool (D) and remove ring (11) that holds insert (10) in the cartridge housing. 8. Remove insert (10) with Tooling (E). 9. Remove O-ring seal (13) and sleeve (12) from insert (10). Remove the seal ring from sleeve (12). 10. Remove deflector (14) and ring (15). 11. Remove bearing (16), sleeve (17) and ring (18). The dye marks put on bearings (19) and (20) are used for identification of the bearings when they are installed.12. Use Tool (F) and remove the ring that holds bearing (19) in position. Remove

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
4Q-1700 Compactor Ar-Loader Custom Product Support Literature for 980G Wheel Loader 9CM00001-UP (MACHINE) POWERED BY 3406C Engine
980G Wheel Loader 2KR00001-UP (MACHINE) POWERED BY 3406C Engine
980G Wheel Loader 9CM00001-UP (MACHINE) POWERED BY 3406C Engine
980G WHEEL LOADER 2SR00001-00650 (MACHINE) POWERED BY 3406 ENGINE
980G WHEEL LOADER 2SR00651-UP (MACHINE) POWERED BY 3406 ENGINE


Parts hood Caterpillar catalog:

3301417 HOOD GP
324D L, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D2 L
2233043 HOOD & GUARD GP
324D, 325D, 325D L, 329D, 329D L
3852309 HOOD GP-ENGINE
336E, 336E L, 336E LN
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.