1246142 HOSE AS Caterpillar parts 30/30, DEUCE HOSE
Rating:
Alternative (cross code) number:
CA1246142
124-6142
1246142
CA1246142
124-6142
1246142
Weight: 2 pounds 1 kg.
Buy HOSE AS 1246142 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,
Number on catalog scheme:
15
For full view, you need register
Information:
MID 027 - CID 1283 - FMI 03
Illustration 1 g01406960
Schematic of the hoist control position sensorThis diagnostic code is associated with the hoist control position sensor. This diagnostic code is recorded when the Power Train/Chassis Electronic Control Module (ECM) reads the signal voltage of the sensor as being too high.The possible causes of this diagnostic code are listed:
Wire M997-PU is shorted to +battery.
The sensor has failed.
The ECM may have failed.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1283 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:EJECTOR BODY. The status of the hoist control position sensor is unknown. The ejector system is unable to eject or retract the ejector plate. The gear of the machine is limited. The gear is limited to the current setting for the gear limit function. The ejector system will remain in the hold position until the hoist control lever is returned to the HOLD position. The ejector system will operate correctly after the diagnostic code has been corrected.Test Step 1. CHECK THE SENSORA. Turn the battery disconnect switch and the key start switch to the ON position.B. Ensure that the diagnostic code is active.C. Observe the status of the diagnostic code. Then, disconnect the machine harness from the sensor.Expected Result:If the sensor is not the cause of the diagnostic code, the diagnostic code remains active. If the sensor has failed, the diagnostic code is no longer active.Results:. YES - The diagnostic code remains active. The sensor has not failed. The machine harness or the ECM may have failed. Proceed to Test Step 2.. NO - The diagnostic code is no longer active. The machine harness is correct and the ECM is operating properly.Repair: The sensor has failed. Replace the sensor. Verify that the new sensor corrects the problem.STOP.Test Step 2. CHECK THE SIGNAL CIRCUIT A. Turn the key start switch and the battery disconnect switch to the OFF position.B. The machine harness remains disconnected from the sensor.C. Disconnect the J1 and J2 connector from the ECM.D. At the J2 connector for the ECM,
Illustration 1 g01406960
Schematic of the hoist control position sensorThis diagnostic code is associated with the hoist control position sensor. This diagnostic code is recorded when the Power Train/Chassis Electronic Control Module (ECM) reads the signal voltage of the sensor as being too high.The possible causes of this diagnostic code are listed:
Wire M997-PU is shorted to +battery.
The sensor has failed.
The ECM may have failed.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1283 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:EJECTOR BODY. The status of the hoist control position sensor is unknown. The ejector system is unable to eject or retract the ejector plate. The gear of the machine is limited. The gear is limited to the current setting for the gear limit function. The ejector system will remain in the hold position until the hoist control lever is returned to the HOLD position. The ejector system will operate correctly after the diagnostic code has been corrected.Test Step 1. CHECK THE SENSORA. Turn the battery disconnect switch and the key start switch to the ON position.B. Ensure that the diagnostic code is active.C. Observe the status of the diagnostic code. Then, disconnect the machine harness from the sensor.Expected Result:If the sensor is not the cause of the diagnostic code, the diagnostic code remains active. If the sensor has failed, the diagnostic code is no longer active.Results:. YES - The diagnostic code remains active. The sensor has not failed. The machine harness or the ECM may have failed. Proceed to Test Step 2.. NO - The diagnostic code is no longer active. The machine harness is correct and the ECM is operating properly.Repair: The sensor has failed. Replace the sensor. Verify that the new sensor corrects the problem.STOP.Test Step 2. CHECK THE SIGNAL CIRCUIT A. Turn the key start switch and the battery disconnect switch to the OFF position.B. The machine harness remains disconnected from the sensor.C. Disconnect the J1 and J2 connector from the ECM.D. At the J2 connector for the ECM,
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
140H, 143H, 14H, 160H, 163H, 16H, 30/30, 320C, 3406, 3406B, 3406C, 572R, 572R II, 578, 583R, 627E, 627F, 627G, 637D, 637E, 637G, 65, 65C, 65E, 75, 75C, 75D, 75E, 814B, 814F, 814F II, 815B, 815F, 815F ...
30/30, 416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, DEUCE
24H, 30/30, 5110B, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 769C, 769D, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 834B, 836, 844, 988B, 988F II, 990, 990 II, 992C, BG-260D, C32, D10R, D8L, D...
120H, 120K, 120K 2, 12K, 12M, 135H, 140G, 140K, 140K 2, 140M, 160K, 30/30, 3114, 3116, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D...
1157426
HOSE
30/30, DEUCE
30/30, DEUCE
1189464
HOSE AS
30/30, AD30, D250E, D250E II, D300E, D300E II, D350E, D350E II, D400E, DEUCE
30/30, AD30, D250E, D250E II, D300E, D300E II, D350E, D350E II, D400E, DEUCE
1279233
HOSE AS
30/30, DEUCE
30/30, DEUCE
1092975
HOSE AS
30/30, CS-531, DEUCE
30/30, CS-531, DEUCE
30/30, DEUCE, M318
1243884
HOSE AS
30/30, DEUCE
30/30, DEUCE
1563438
HOSE
DEUCE
DEUCE
1243852
HOSE AS
30/30, DEUCE
30/30, DEUCE
1197697
HOSE AS
30/30, AP-1055D, AP-655C, BG-2455D, CB-544, CB-545, DEUCE, PF-300C, PS-300B
30/30, AP-1055D, AP-655C, BG-2455D, CB-544, CB-545, DEUCE, PF-300C, PS-300B
1129439
HOSE AS
30/30, 776D, 777D, 914G, AP-1055D, AP-900B, DEUCE, IT14G, IT14G2
30/30, 776D, 777D, 914G, AP-1055D, AP-900B, DEUCE, IT14G, IT14G2
1101986
HOSE AS
30/30, DEUCE, RM-350B, SM-350
30/30, DEUCE, RM-350B, SM-350
8W6649
HOSE AS
30/30, 657E, 776C, 776D, 777D, DEUCE
30/30, 657E, 776C, 776D, 777D, DEUCE
1189464
HOSE AS
30/30, AD30, D250E, D250E II, D300E, D300E II, D350E, D350E II, D400E, DEUCE
30/30, AD30, D250E, D250E II, D300E, D300E II, D350E, D350E II, D400E, DEUCE
1275750
HOSE AS
30/30, AP-1055D, BG-2455D, DEUCE
30/30, AP-1055D, BG-2455D, DEUCE
1249036
HOSE AS
30/30, DEUCE
30/30, DEUCE
1249035
HOSE AS
30/30, DEUCE
30/30, DEUCE
1249031
HOSE AS
30/30, DEUCE
30/30, DEUCE
1249030
HOSE AS
30/30, DEUCE
30/30, DEUCE
1249026
HOSE AS
30/30, DEUCE
30/30, DEUCE