AVSPARE.COM
parts catalog

HOSE AS 1246382 - Caterpillar



1246382 HOSE AS Caterpillar parts 24H, 836G, 836H HOSE
Rating:
35
Alternative (cross code) number:
CA1246382
124-6382
1246382
Caterpillar 1246382 HOSE AS

Buy HOSE AS 1246382 Caterpillar genuine, new aftermarket tractor parts with delivery
LANDFILL COMPACTOR, MOTOR GRADER,

Compatible equipment models: 1246382:

LANDFILL COMPACTOR  836G   836H  
MOTOR GRADER  24H   Caterpillar
Number on catalog scheme: 6
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06327243
If necessary, use Tooling (A) to ensure that number one piston is at top dead center on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No.1 Piston". for the correct procedure.
Ensure that Tooling (C) is installed in hole (Y) in the cylinder block. Use Tooling (C) to lock the crankshaft in the correct position.Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the crankshaft during repairs.
Illustration 2 g06327245
Ensure that Tooling (C) is installed into hole (X) in gear (1).
Illustration 3 g06327249
Clean idler gear (8) and inspect idler gear (8) for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace idler gear (8).
Clean hub (14) and inspect hub (14) for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace hub (14).
Illustration 4 g06327106
Lubricate hub (14) with clean engine oil. Install hub (14) into idler gear (8). Ensure that the timing marks are toward the front of the idler gear.
Illustration 5 g06327255
Illustration 6 g06327092
Align the timing mark on idler gear (8) with the timing mark on camshaft gear (1) and engine oil pump gear (2). Install the assembly of idler gear (8) and hub (14) into the recess in the timing case. Ensure that oil Hole (Z) is to the top of the hub.Note: The idler gear must be tilted during installation. Ensure that the holes in the hub are aligned with the holes in the cylinder block.
Clean plate (12) and inspect the plate for wear or damage. If necessary, replace plate (12).
Lubricate plate (12) with clean engine oil. Align the holes in plate (12) with the holes in the hub. Install plate (12) in the original orientation.
Install bolts (13).
Remove Tooling (B) and Tooling (C).Note: Ensure that timing marks are aligned, before removing Tooling (B) and Tooling (C).
Tighten bolts (13) to a torque of 44 N m (32 lb ft).
Use Tooling (D) to measure the end play of camshaft gear (1). Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (D) to measure the backlash between idler gear (8) and camshaft gear (1). Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (D) to measure the backlash between idler gear (8) and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Illustration 7 g06327258
Install a new O-ring seal (3) to plug (4). Install plug (4) to the cylinder block. Tighten plug (4) to a torque of 21 N m (186 lb in).
Lubricate the teeth of the gears with clean engine oil.End

Caterpillar parts catalog:

Caterpillar parts catalog
24H Motor Grader 7KK00001-UP (MACHINE) POWERED BY 3412E Engine
836G Landfill Compactor BRL00001-UP (MACHINE) POWERED BY 3456 Engine
836H Landfill Compactor BXD00001-UP (MACHINE) POWERED BY C18 Engine


Parts hose Caterpillar catalog:

2221980 HOSE AS
824K, 825K, 834G, 834H, 834K, 836G, 836H, 836K
1977596 HOSE AS
824C, 824G II, 824H, 825G II, 825H
1977595 HOSE AS
824G II, 824H, 825G II, 825H
2019673 HOSE AS
824G II, 825G II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.