AVSPARE.COM
parts catalog

HOSE AS 1246510 - Caterpillar



1246510 HOSE AS Caterpillar parts M312 HOSE
Rating:
66
Alternative (cross code) number:
CA1246510
124-6510
1246510
Caterpillar 1246510 HOSE AS

Buy HOSE AS 1246510 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEELED EXCAVATOR,

Compatible equipment models: 1246510:

WHEELED EXCAVATOR  M312   Caterpillar
Number on catalog scheme: 11
 
  For full view, you need register

Information:


Illustration 1 g02160341
Schematic of the Cat Data Link CircuitThis diagnostic code is recorded when the LH Operator ECM does not receive the expected information from the Alternate Control (RH) Station ECM.The likely possible causes of this diagnostic code are listed below:
The software that is installed on the Alternate Control (RH) Station ECM is incorrect.
The software that is installed on the LH Operator ECM is incorrect.System Response:When this diagnostic code is active, the following occurs:
The fault horn is active.
Operator station fault lamp is active.
The following pop-up message shows on graphical display: "Loss of communication with Auxiliary Station. Material feed automatic function may be disabled. Activate left station to propel machine."Note: The LH Operator ECM is located under the LH Operator Platform.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify that the following information is correct:
The part number of the software of the LH Operator ECM
The part number of the Alternate Control (RH) Station ECM software
The part number of the LH Operator ECM
The part number of the Alternate Control (RH) Station ECM Note: Consult the Business Unit that produces the product for the correct part numbers of the configuration software. Expected Result:All part numbers are correct. Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All part numbers are NOT correct. The part number of the LH Operator ECM may be incorrect. The part number of the Alternate Control (RH) Station ECM may be incorrect. The incorrect configuration software may also be installed. Repair: Replace the incorrect ECM with an ECM that has the correct part number. Flash the correct configuration software. See Troubleshooting, "Electronic Control Module - Flash Program".STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating.
Check the wires at the connector.
Check each wire for nicks or signs of abrasion in the insulation.
Check for moisture at the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and check each socket of the machine harness connectors. Expected Result:The machine harness connectors are tight and free of corrosion. Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to test step 3.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK FOR SHORTS TO GROUND.
The disconnect switch remains in the OFF position.
Disconnect the machine harness from all electronic control modules that use the Cat Data Link.
At the machine harness for the LH Operator ECM, measure the resistance between frame ground and connector contacts J1-10 (wire 944-OR) and J1-20 (wire 945-BR) of the Cat Data Link circuit. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to test step 4.
NOT OK - The resistance is less than 5000 ohms. The

Caterpillar parts catalog:

Caterpillar parts catalog
M312 Excavator 6TL00001-00409 (MACHINE) POWERED BY 3054 Engine
M312 Excavator 6TL00410-UP (MACHINE) POWERED BY 3054 Engine


Parts hose Caterpillar catalog:

5P0767 HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
1434534 HOSE
236, 248, 267, 287, 3034, 3054, 3054B, 312, 312B L, 312C, 315, 315B L, 317, 416C, 416D, 420D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 908, 914G, AP-800C, BG-225B, C2.2, CB-534C, CB-535B,...
1328375 HOSE AS
M312, M315, M318
1467283 HOSE AS
M312, M315, M318, M320
1134138 HOSE AS
M312, M315, M318
1428382 HOSE AS
M312, M315, M318, M320
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.