HOSE AS 1247094 - Caterpillar

1247094 HOSE AS Caterpillar parts CB-534B, CB-534C, CB-544, CB-545 HOSE

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1247094
124-7094
1247094

Weight: 0.52 pounds 0 kg.

Buy HOSE AS 1247094 Caterpillar genuine, new aftermarket tractor parts with delivery
VIBRATORY COMPACTOR,

Compatible equipment models: 1247094:

VIBRATORY COMPACTOR CB-534B CB-534C CB-544 CB-545 Caterpillar

Number on catalog scheme: 8

Caterpillar 1247094 Parts scheme HOSE AS

For full view, you need register

Information:

Illustration 1 g01338888
Connections of the transmission output speed sensor 2
This diagnostic code is associated with the transmission output speed sensor 2. The FMI 12 means that the ECM has determined that the signal frequency is not within the expected range.System Response:A diagnostic code will be displayed on the Caterpillar Electronic Technician (Cat ET). The tractor will operate normally unless more than one speed sensor has failed.Test Step 1. CHECK THE RESISTANCE OF THE CASE OF THE SENSOR .
Turn the key start switch and the disconnect switch (if equipped) to the OFF position.
Disconnect the machine harness connector from the sensor.
Measure the resistance from contact 1 (wire E906-OR(Orange)) and from contact 2 (wire E907-GY(Grey)) to the case of the sensor.Expected Result:The resistance is greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. Proceed to Test Step 2.
NOT OK - The resistance is NOT greater than 5000 ohms. The speed sensor has failed.Repair: Replace the sensor.STOPTest Step 2. CHECK THE RESISTANCE OF THE SENSOR.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Measure the resistance between contact 1 (wire E906-OR(Orange)) and contact 2 (wire E907-GY(Grey)) of the connector of the sensor.Expected Result:The resistance is between 600 and 1800 ohms.Results:
OK - The resistance is between 600 and 1800 ohms. The resistance is correct. Proceed to Test Step 3.
NOT OK - The resistance is NOT between 600 and 1800 ohms. The resistance is not correct. The sensor has failed.Repair: Replace the sensor.STOPTest Step 3. CHECK FOR AN OPEN HARNESS.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Reconnect the machine harness connector to the sensor.
Disconnect the machine harness connectors J1 and J2 from the ECM.
At the machine harness connector J1, measure the resistance from contact J1-32 to contact J1-33.Expected Result:The resistance is between 600 and 1200 ohms.Results:
OK - The resistance is between 600 and 1800 ohms. The circuit is correct. Proceed to Test Step 4.
NOT OK - The resistance is NOT between 600 and 1800 ohms. The circuit is open in the machine harness.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 4. CHECK FOR A SHORT IN THE RETURN CIRCUIT OF THE MACHINE HARNESS.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Disconnect the machine harness from the sensor.
At the machine harness connector J1, measure the resistance between contacts J1-32 and J1-33 to all sources of ground.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. Proceed to Test Step5.
NOT OK - There is a short in the machine harness.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 5. INSPECT THE SENSOR AND ADJUST THE SENSOR.
The key start switch and the disconnect switch (if equipped) remain in the OFF position. The sensor remains disconnected from the machine harness.
Remove the speed sensor. Inspect the sensor for damage or the presence of foreign material on the tip.Expected Result:The sensor is free of foreign material and