AVSPARE.COM
parts catalog

HOSE AS 1694960 - Caterpillar


1694960 HOSE AS Caterpillar parts 539
Rating:
72
Alternative (cross code) number:
CA1694960
169-4960
1694960
Caterpillar 1694960 HOSE AS
Weight: 1 pounds 0 kg.

Buy HOSE AS 1694960 Caterpillar genuine, new aftermarket tractor parts with delivery
KNUCKLEBOOM LOADER,

Compatible equipment models: 1694960:

KNUCKLEBOOM LOADER  539   Caterpillar
Number on catalog scheme: 24
 
  For full view, you need register

Information:

Do not put oil on the bearings until the bearing clearance has been checked.1. Install bearings (1) in the connecting rods they were removed from. Make sure the tab in each bearing is in alignment with the notch in each connecting rod.2. Install bearings (2) in the cylinder block. Make sure the tab in each bearing is in alignment with the notch in the cylinder block. 3. Install pin (3) in the end of the crankshaft. Install the pin so that it extends a maximum of 6.4 mm (.252 in) above the surface. 4. Install the dowel in the crankshaft that puts gear (4) in the correct position. Install the dowel so that it extends 4.1 0.5 mm (.161 .020 in) above the surface of the crankshaft.5. Heat gear (4) to a maximum temperature of 233° C (451° F). Gear (4) must be installed on the crankshaft with the "V" timing mark toward the outside.6. Install gear (4) on the crankshaft. Make sure the notch in the gear is in alignment with the dowel on the crankshaft. The dimension from the rear face of the gear to the front face of the crankshaft must be 45.54 0.25 mm (1.793 .010 in). 7. Fasten Tooling (A) and a hoist to the crankshaft (5) as shown. Install the crankshaft in the engine. The weight of the crankshaft is approximately 131 kg (290 lb). 8. Make sure that "V" mark (6) on the crankshaft is in alignment with "V" mark (7) on the idler gear. The side of each thrust plate (8) with the words "BLOCK SIDE" must be installed with this side toward the cylinder block.9. Put clean oil on thrust plates (8). Install thrust plates (8) next to the center main bearings. Do not put oil on bearings (9) until the bearing clearances have been checked.10. Put bearings (9) in their original position in crankshaft main bearing caps (10).11. Check the crankshaft main bearing clearance with Plastigage as follows:a. Put a piece of Plastigage between the crankshaft bearing journal surface and bearing (9).b. Install the crankshaft main bearing caps (10) with the arrow on each cap toward the front of cylinder block. Each crankshaft main bearing cap has a number on the bottom surface and must be installed in the same position as the correct number on the left side of the cylinder block.c. Put 2P-2506 Thread Lubricant on the threads of the cap bolts. Install the cap bolts finger tight.d. Tighten the bolts on the tab end of the caps first to a torque of 258 14 N m (190 10 lb ft).e. Tighten the bolts on the other end of the caps to a torque of 258 14 N m (190 10 lb ft).
Do not use an impact wrench to tighten the bolts the additional 120 degrees.
f. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end of the cap

Caterpillar parts catalog:

Caterpillar parts catalog
539 Knuckle Boom Loader 1PZ00001-UP (MACHINE) POWERED BY 3126 Engine


Parts hose Caterpillar catalog:

5P0767 HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
5P0743 HOSE
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 160K, 160M, 16M, 216, 228, 236, 236B, 236D, 242B, 242D, 246D, 247, 247B, 248, 257D, 259D, 262D, 267, 267B, 268B, 272D, 272D XHP, 277D, 279D, 287...
1032529 HOSE
120H, 120H ES, 120H NA, 120M 2, 135H, 135H NA, 236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 2864C, 287D, 289D, 299D, 299D XHP, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR...
7C3615 HOSE
120H, 120H ES, 120H NA, 135H, 135H NA, 3114, 3116, 3126, 320 L, 322B L, 322B LN, 322C, 322C FM, 325, 325 LN, 325B, 325B L, 525B, 533, 535B, 539, 543, 550, 570, 574, 580, 613C II, 938G, 950F, 950F II, ...
1085746 HOSE
120H ES, 3116, 3126, 322B L, 322B LN, 322C, 322C FM, 325B, 325B L, 525B, 533, 535B, 539, 543, 550, 570, 574, 580, 613C II, 938G, 950F, 950F II, 950G, 960F, 962G, 963B, 963C, AP-1000B, AP-1055B, BG-245...
1360588 HOSE
525B, 535B, 539, 550, 570, 574, 580, 938G, 950F, 950F II, 950G, 960F, 962G, IT38G, IT62G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.