AVSPARE.COM
parts catalog

HOSE AS. 3078762 - Caterpillar



3078762 HOSE AS. Caterpillar parts HOSE
Rating:
51
Alternative (cross code) number:
CA3078762
307-8762
3078762
Caterpillar 3078762 HOSE AS.

Buy HOSE AS. 3078762 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g01312020
Remove belt (1). Refer to Operation and Maintenance Manual, "Belt - Inspect/Adjust/Replace".
Disconnect harness assemblies (3).
Disconnect clip (4).
Remove bolt (2) and remove bolt (5).
Set refrigerant compressor (6) out of the way.
Illustration 2 g01312082
Disconnect hose (9).
Disconnect clips (7).
Disconnect harness assembly (8).
Disconnect harness assemblies (10).
Disconnect clip (11).
Illustration 3 g01312148
Disconnect hoses (12).
Illustration 4 g01312152
Disconnect cable assembly (13).
Disconnect ground strap (14).
Disconnect clip (15).
Illustration 5 g01312163
Remove clip (16) and set refrigerant accumulator (17) to the side.
Disconnect tube assemblies (18) and (20).
Disconnect harness assembly (19).
Illustration 6 g01312177
Remove cover (21).
Illustration 7 g01312181Note: The transmission oil cooler was removed from this picture for clarity purposes.
Remove bolts (23).
Disconnect hose assembly (24).
Remove bracket assembly (22).
Illustration 8 g01312304
Attach Tooling (B) to engine (25). The weight of engine (25) is approximately 1180 kg (2600 lb).
Use a suitable lifting device to attach one end of Tooling (C) to Tooling (B). Attach the other end of Tooling (C) to engine (25). Attach a suitable lifting device to Tooling (C).
Illustration 9 g01312337
Remove bolts (26).
Disconnect hose assembly (27) from engine (25).
Illustration 10 g06228047
Position Tooling (A) under rear guard assembly (28). The weight of rear guard assembly (28) is approximately 75 kg (165 lb).
Remove bolts (29).
Use Tooling (A) to lower rear guard assembly (28). Remove rear guard assembly (28).
Illustration 11 g01312348
Use the suitable lifting device that is attached to Tooling (B) and Tooling (C) to raise the engine. Raise the engine enough to place Suitable Cribbing (X) between transmission housing (30) and rear axle housing (31).
Illustration 12 g01312367
Remove bolts (33) from torque converter housing (32).
Use the suitable lifting device that is attached to Tooling (B) and Tooling (C) to remove the engine from the machine. Place the engine onto suitable cribbing.
Illustration 13 g01312390
Remove O-ring seal (34) and O-ring seal (35).


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.