AVSPARE.COM
parts catalog

HOSE AS 3079046 - Caterpillar



3079046 HOSE AS Caterpillar parts 307D, 308D HOSE
Rating:
13
Alternative (cross code) number:
CA3079046
307-9046
3079046
Caterpillar 3079046 HOSE AS

Buy HOSE AS 3079046 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR,

Compatible equipment models: 3079046:

MINI HYD EXCAVATOR  307D   308D   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9634 Puller Stud 1
9U-6832 Nut 1
5P-8712 Bushing 1
316-1489 Hydraulic Cylinder Gp 1
5P-8625 Spacer 1
284-2368 Bearing Puller Adapter 1 Start By:
Remove the boom. Refer to Disassembly and Assembly, "Boom - Remove".
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Do not use threaded rods that have not been hardened as tooling with hydraulic cylinders. The maximum rated tonnage should be stamped on one end of the puller studs. Do not use threaded rods that have not been stamped with the rated tonnage.
Illustration 1 g00479266
Remove lip seal (1).
Illustration 2 g00479267
Use Tooling (A) to remove the sleeve bearing.
Repeat Steps 1 through 2 to remove the lip seal and the sleeve bearing from the other side of the boom.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 1P-0520 Bearing and Seal Driver 1
C 452-6006 Molybdenum Grease -
Make sure that the bores for the sleeve bearings are free of paint and grease prior to the installation of the sleeve bearings. Coat the sleeve bearings and the bearing bores with Tooling (C) prior to the installation of the sleeve bearings in the bores. Sleeve bearings must be installed with the identification numbers toward the outside of the boom.Note: Make sure that the bearings are installed in the bore so that the identification numbers of the bearings are facing outward.
Illustration 3 g00599079
(X) Boom
(Y) Bearing
Lower the temperature of the sleeve bearings to −40 °C (−40 °F). Use Tooling (B) to install the sleeve bearing in the pin bore at the foot of the boom. Install the sleeve bearing until Dimension (a) is 9.5 0.8 mm (0.37 0.03 inch) below the outside surface of the boom.
Illustration 4 g00479266
Use Tooling (B) to install lip seal (1) in the pin bore at the foot of the boom. Install the seal with the sealing lip toward the outside of the boom. Install the lip seal until the lip seal makes contact with the sleeve bearing.
Repeat Steps 2 through 3 to install the sleeve bearing and the lip seal on the other side of the boom.
Put a thin coat of Tooling (C) on the sleeve bearings. Put a thin coat of Tooling (C) on the lips of lip seals (1).End By:
Install the boom. Refer to Disassembly and Assembly, "Boom - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
308D Mini Hydraulic Excavator GBT00001-UP (MACHINE) POWERED BY 4M40 Engine
307D Mini Hydraulic Excavator WZX00001-UP (MACHINE)


Parts hose Caterpillar catalog:

5P1442 HOSE
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140B, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, ...
5P0767 HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
5P1420 HOSE
120M, 12M, 216, 216B, 216B3, 226B, 226B3, 228, 2290, 232B, 235C, 236, 236B, 236B3, 236D, 2384C, 2390, 2391, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 2484C, 2491, 252B, 252B3, 256C, 257B, ...
1032529 HOSE
120H, 120H ES, 120H NA, 120M 2, 135H, 135H NA, 236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 2864C, 287D, 289D, 299D, 299D XHP, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR...
7Y1976 HOSE-WATER
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 30...
1087203 HOSE AS
307C, 308D, 312C, 312C L, 314C, 316E L, 318C, 318E L, 319C, 320B, 320C, 320C L, 320D FM, 320D L, 320D LN, 321C, 321D LCR, 322B, 322B L, 322C, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D ...
5I4396 HOSE AS
307C, 308D, 311F LRR, 312D, 314D CR, 314D LCR, 314E CR, 314E LCR, 315D L, 316E L, 318C, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 3...
7I8252 HOSE AS
307C, 308D, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 315C, 315D L, 316E L, 318C, 318E L, 319D, 319D L, 320B, 320C, 32...
0875764 HOSE AS
307C, 307D, 307E, 311C, 311D LRR, 311F LRR, 312D, 312D L, 314C, 314D LCR, 314E LCR, 320B, 320C, 320C FM, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B, 322B LN...
3264362 HOSE AS
307D, 308D, 345C, 345C L, 345D L, PIN GRAB
3264363 HOSE AS
307D, 308D, 345C, 345C L, 345D L, PIN GRAB
3860402 HOSE AS
307D, 307E, 308E
3132315 HOSE AS
307D, 307E, 308E
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.