AVSPARE.COM
parts catalog

HOSE AS 3534869 - Caterpillar



3534869 HOSE AS Caterpillar parts HOSE
Rating:
21
Alternative (cross code) number:
CA3534869
353-4869
3534869
Caterpillar 3534869 HOSE AS

Buy HOSE AS 3534869 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Introduction
The boom hydraulic circuit contains a regeneration circuit. This regeneration circuit allows the return oil from the head end of the boom cylinders to be supplied to the rod end of the boom cylinders during the BOOM DOWN operation. The proportional reducing valve (PRV) for the boom regeneration valve controls the amount of pilot pressure from the joystick to the boom down regeneration valve. The PRV for the boom regeneration valve is controlled by the machine ECM.Required Tools
Illustration 1 g01623868
Tooling group "B"
198-4240 Digital Pressure Indicator Gp
Table 1
Tool Item Qty Part Number Description
B 198-4240 Digital Pressure Indicator Gp
B1 1 198-4234 Indicator
B2 1 198-4237 Pressure Sensor 3447 kPa (500 psi)
B3 1 198-4236 Extension Cable Machine Preparation
The following procedures must be completed before performing the calibration.
Set the pilot pressure to the specifications in Testing and Adjusting, "Relief Valve (Pilot) - Test and Adjust" for the machine.
Calibrate the power shift pressure. Refer to Testing and Adjusting, "Solenoid Valve (Proportional Reducing) - Calibrate (Power Shift Pressure)" for the machine.
Calibrate the proportional reducing valve for negative flow control. Refer to Testing and Adjusting, "Solenoid Valve (Proportional Reducing) - Calibrate (Negative Flow Control)" for the machine.
Position the machine on level ground.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Illustration 2 g03889567
Pressure tap for the proportional reducing valve (boom regeneration valve) as viewed from above control valve.
Connect a 3447 kPa (500 psi) pressure sensor to the pressure tap for the boom regeneration valve.
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Place the machine implements on the ground at maximum reach.
Place the hydraulic activation lever in the UNLOCK position. Calibration Procedure
Enter the service mode. Input the password "9992".
Illustration 3 g02308313
Select "Boom Down Regen Valve" from the "Calibrations" menu.
Press the OK key in order to start the calibration. The engine RPM will automatically drop to the equivalence of engine speed dial 1.
Confirm the notes on the monitor display. Set up the test conditions in accordance with the instructions. Press the OK key.
Move the joystick for BOOM DOWN to the full down position and hold the joystick in this position.
Illustration 4 g02308353
Use the arrows to adjust the pressure until the pressure reading for the boom regeneration valve is at 500 50 kPa (73 7 psi). Press the OK key.
Move the joystick for BOOM DOWN to the NEUTRAL position.
Confirm notes on the monitor display. Set up the test conditions in accordance with the instructions. Press the OK key.
Move the joystick for BOOM DOWN to the full down position and hold the joystick in this position.
Illustration 5 g02313613
Use the arrows to adjust the pressure until the pressure reading for the boom regeneration valve is at 2500 50 kPa (363 7 psi). Press the OK key.
Move the joystick for BOOM DOWN to the NEUTRAL


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.