AVSPARE.COM
parts catalog

HOSE AS-OIL SUPPLY 3535171 - Caterpillar



3535171 HOSE AS-OIL SUPPLY Caterpillar parts 627H, 627K, 725C HOSE
Rating:
76
Alternative (cross code) number:
CA3535171
353-5171
3535171
Caterpillar 3535171 HOSE AS-OIL SUPPLY
Weight: 0.66 pounds 0 kg.

Buy HOSE AS-OIL SUPPLY 3535171 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK, WHEEL TRACTOR-SCRAPER,

Compatible equipment models: 3535171:

ARTICULATED TRUCK  725C  
WHEEL TRACTOR  627H  
WHEEL TRACTOR-SCRAPER  627K   Caterpillar
  For full view, you need register

Information:

start by:a) remove vibration damper 1. Use tool (A) to remove crankshaft front seal (1). 2. Install tool (C) in the bore.3. Install tool (B) between tool (C) and the wear sleeve. Turn tool (B) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in two or more places until the wear sleeve is loose.4. Remove tool (C). Remove wear sleeve by hand.Install Crankshaft Front Seal And Wear Sleeve
The crankshaft seal and wear sleeve must be installed together.1. Install the crankshaft front seal and wear sleeve with tooling (A) as follows: a) Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 8M8060 Quick Cure Primer. Make an application of 9S3265 Retaining Compound to crankshaft outside diameter and wear sleeve inside diameter before the wear sleeve is installed on the crankshaft. b) Install locator (2) and the bolts on the front of the crankshaft.c) Put clean engine oil on the seal lip of seal (6) and on the outside diameter of wear sleeve (1). Install seal (6) on wear sleeve (1) as shown. Make sure the lip of the seal is toward the inside of the engine and the outside diameter bevel of the wear sleeve is toward the outside of the engine.d) Put wear sleeve (1) and seal (6) in position on locator (2).e) Install spacer (3) on the stud of locator (2).f) Put installer (5) in position on locator (2).g) Put clean engine oil on the face of nut (4) and its contact area on installer (5). Install nut (4) on locator (2).h) Tighten nut (4) until the inside surface of installer (5) comes in contact with spacer (3).i) Remove tooling (A) and check the wear sleeve and seal for the correct position after installation. The distance from the front face of the crankshaft to the front edge of the wear sleeve must be .06 .02 in. (1.52 0.5 mm).end by:a) install vibration damper


Parts hose Caterpillar catalog:

3964861 HOSE
627H, 627K, 627K LRC
3736694 HOSE AS
623H, 623K, 623K LRC
3736693 HOSE AS
623H, 623K, 623K LRC
3736692 HOSE AS
623H, 623K, 623K LRC
3710980 HOSE AS
623H, 623K, 623K LRC
3709810 HOSE AS
623H, 623K, 623K LRC
3353561 HOSE
627H, 627K, D8T
3086808 HOSE
627H, 966K, 966M, 966M XE, 972K, 972M, 972M XE
2546034 HOSE-ELBOW
525C, 535C, 545C, 627H, 627K, 627K LRC, 815B, D7E, D7E LGP
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.