parts catalog

HOSE AS 3599290 - Caterpillar

3599290 HOSE AS Caterpillar parts 627H HOSE
Alternative (cross code) number:
Caterpillar 3599290 HOSE AS

Buy HOSE AS 3599290 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 3599290:

WHEEL TRACTOR  627H   Caterpillar
Number on catalog scheme: 10
  For full view, you need register


To prevent possible injury, do not use the starter to turn the flywheel. Hot engine components can cause burns. Allow additional time for the engine to cool before measuring valve clearance.
This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Valve Lash Check
An adjustment is NOT NECESSARY if the measurement of the valve lash is in the acceptable range. Check the valve lash while the engine is stopped. The range is specified in Table 1.
Table 1
Valve Lash
Valves Acceptable Range for Valve Lash
Inlet 0.38 0.08 mm (0.015 0.003 inch)
Exhaust 0.76 .08 mm (0.030 0.003 inch) If the measurement is not within this range adjustment is necessary. Refer to Testing And Adjusting, "Valve Lash Adjustment".Valve Lash Adjustment
Illustration 1 g00561261
(A) Inlet valves
(B) Exhaust valves
(C) Left side of the engine
(D) Cylinder number
(E) Front of the engine
(F) Right side of the engine
(G) Flywheel end of the engine
Illustration 2 g00506544
(1) Valve adjustment locknut
(2) Exhaust adjustment screw
(3) Valve adjustment locknut
(4) Inlet adjustment screw
(5) Feeler gauge
Table 2
Valve Lash
Valves Gauge Dimension
Inlet 0.38 mm (0.015 inch)
Exhaust 0.76 mm (0.030 inch) Adjust the valve lash while the engine is stopped. Use the following procedure in order to adjust the valves:
Put the No. 1 piston at the top center position. Note: If the engine is equipped with an engine compression brake, loosen the adjusting screw for the lash on the slave piston for the compression brake prior to adjusting the engine valve lash. Refer to the Testing and Adjusting, "Slave Piston Lash - Adjust" topic in order to adjust the slave piston lash.Note: See Testing and Adjusting, "Finding Top Center Position for the No. 1 Piston" for further details.
With No. 1 piston at the top center position of the compression stroke, an adjustment can be made to the valves. Before any adjustments are made, lightly tap each rocker arm at the top of the adjustment screw. Use a soft mallet to ensure that the lifter roller seats against the camshaft's base circle.
Make an adjustment to the valve lash on the inlet valves for cylinders 1, 2, and 4.
Loosen valve adjustment locknut (3).
Place the appropriate

Caterpillar parts catalog:

Caterpillar parts catalog
627H Wheel Tractor Scraper LCT00001-UP (MACHINE)

Parts hose Caterpillar catalog:

5P1251 HOSE
120K, 120K 2, 120M, 12K, 12M, 140K, 140K 2, 140M, 160K, 160M, 16M, 235, 245, 245B, 24H, 24M, 3126, 3126B, 3176B, 3176C, 3196, 3208, 3304, 3306, 3306B, 3406, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 341...
5P0767 HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
1316645 HOSE
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 1673C, 16H, 16M, 215B, 235B, 235D, 3176C, 3196, 330, 330 L...
5P1420 HOSE
120M, 12M, 216, 216B, 216B3, 226B, 226B3, 228, 2290, 232B, 235C, 236, 236B, 236B3, 236D, 2384C, 2390, 2391, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 2484C, 2491, 252B, 252B3, 256C, 257B, ...
1361953 HOSE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
1945171 HOSE
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3,...
9X2133 HOSE
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 303, 303.5C, 303.5D, 303.5E, 303C CR, 3...
5P1293 HOSE
120G, 120H, 120H ES, 120H NA, 12G, 130G, 135H, 135H NA, 14H, 16H, 16M, 2384C, 2484C, 322 FM L, 325 L, 3412, 3412C, 3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 5130, 5130B, 521B, 522B, 559C, 579C, 61...
2423360 HOSE
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 3126, 3126B, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL...
8N5991 HOSE
3412, 3512C, 3516C, 627H, 627K LRC, 773F, 775F, 776C, 777, 777B, 777F, 824K, 825K, 826K, 834K, 836K, 988K, AD55B, C27, C32, G3412, G3508, G3508B, G3512E, G3516, G3516B, G3516C, G3520C, TH48-E70
2590, 521B, 522B, 541, 541 2, 551, 552, 552 2, 627H, 627K, 627K LRC, 631D, 637D, 966F II, AP-1055D, BG-2455D, BG-260D, CB-14B, D8R, PF-300C, PM3508, PM3516, PS-300B
5P1292 HOSE
140, 141, 153, 163, 225, 517, 518, 518C, 527, 528, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637D, 637E, 637G, 770, 772, 773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, 777G, 834, 953D, 988, 9...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.