AVSPARE.COM
parts catalog

HOSE AS 3967634 - Caterpillar



3967634 HOSE AS Caterpillar parts HOSE
Rating:
11
Alternative (cross code) number:
CA3967634
396-7634
3967634
Caterpillar 3967634 HOSE AS

Buy HOSE AS 3967634 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 24
 
  For full view, you need register

Information:


Illustration 1 g00892504
Typical example
(1) Cylinder liner Outside diameter of cylinder liner ... 104.25 to 104.28 mm (4.105 to 4.106 inch)Inside diameter of cylinder liner ... 100.00 to 100.03 mm (3.937 to 3.938 inch)Maximum permissible wear of cylinder liner bore ... 0.25 mm (0.010 inch)Interference fit of cylinder liner in cylinder block ... 0.03 to 0.08 mm (0.001 to 0.003 inch)Flange thickness of cylinder liner ... 3.81 to 3.86 mm (0.150 to 0.152 inch)The projection of the liner flange can be 0.10 mm (0.004 inch) above to 0.10 mm (0.004 inch) below the top face of the cylinder block. (2) Plug with baffle plates (if equipped) Orientation of baffle plates to the vertical plane ... +/- 5 degreesDepth of plug from face of cylinder block ... 3 mm (0.12 inch) (3) Cylinder block Diameter of the bore for the cylinder liner ... 104.20 to 104.23 mm (4.103 to 4.104 inch)Depth of the recess for the cylinder liner flange ... 3.81 to 3.91 mm (0.150 to 0.154 inch)Diameter of the recess for the cylinder liner flange ... 107.82 to 107.95 mm (4.245 to 4.250 inch) (4) Tighten the bolts that fasten the housing for the crankshaft rear seal to the cylinder block to the following torque. ... 22 N m (16 lb ft) (5) Tighten the bolts that fasten the housing for the crankshaft rear seal to the bridge to the following torque. M6 ... 13 N m (10 lb ft)M8 ... 22 N m (16 lb ft) (6) Bridge bolt Use the following procedure in order to install the bridge bolts.
Use a straight edge in order to ensure that the bridge is aligned with the front face of the cylinder block.
Evenly tighten the bridge bolts to a torque of 16 N m (12 lb ft).
When the bridge is installed on the cylinder block, apply a thin bead of 8T-9013 Silicone Sealant into the groove at each end of the bridge. (7) Main bearing cap bolts Use the following procedure in order to install the main bearing cap bolts.
Apply clean engine oil to the threads of the main bearing cap bolts.
Put the main bearing caps in the correct position that is indicated by a number on the top of the main bearing cap. Install the main bearing caps with the locating tabs in correct alignment with the recess in the cylinder block.
Evenly tighten the main bearing cap bolts to a torque of 265 N m (195 lb ft). (8) Bore in the cylinder block for the main bearings ... 80.416 to 80.442 mm (3.1660 to 3.1670 inch) (9) Camshaft bearing Inside diameter of the camshaft bearing for the number 1

Caterpillar parts catalog:

Caterpillar parts catalog
637K Wheel Tractor Scraper WTY00001-UP (MACHINE)
631K OEM Wheel-Tractor Sctraper WT400001-UP (MACHINE) POWERED BY C18 Engine
631K OEM Wheel-Tractor Scraper WT600001-UP (MACHINE) POWERED BY C18 Engine
631K Wheel Tractor Scraper WTR00001-UP (MACHINE) POWERED BY C18 ENGINE
637K Wheel Tractor Scraper WTS00001-UP (MACHINE)
637K Wheel Tractor Scraper WTT00001-UP (MACHINE)
631K Wheel Tractor Scraper WTW00001-UP (MACHINE) POWERED BY C18 Engine
637K Wheel Tractor Scraper WTX00001-UP (MACHINE)


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.