AVSPARE.COM
parts catalog

HOSE AS 4646841 - Caterpillar



4646841 HOSE AS Caterpillar parts HOSE
Rating:
51
Alternative (cross code) number:
CA4646841
464-6841
4646841
Caterpillar 4646841 HOSE AS

Buy HOSE AS 4646841 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 17
 
  For full view, you need register

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01424862
Ensure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material.
Put clean engine oil on all parts of the cartridge assembly.
Install washer (23) and bearing (22) in cartridge housing (25). Ensure that the identification mark on bearing (2) is positioned upward.
Install snap rings (21) and (24) in cartridge housing (25) with Tooling (E).
Illustration 2 g01424860
Install top bearing (20) and the washer in the cartridge housing. Ensure that the identification marks are positioned upward.
Install the O-ring seal and thrust bearing (19) in the cartridge housing.
Illustration 3 g01424859
Illustration 4 g01424857
Install collar (18) on the opposite side of back plate assembly (17).
Install the seal ring in spacer (15). Install the spacer (15) in back plate assembly (17). Install back plate assembly (17) to the cartridge housing.
Position locks (16) and install bolts (14). Tighten bolts (14) and bend the tabs on locks (16).
Illustration 5 g01424852Note: Put Tooling (G) in the groove for seal ring (12).
Install turbine shaft (11) in Tooling (B). Install seal ring (12) and shroud (13) on turbine shaft (13).
Illustration 6 g01424825
Install washer (10) and bearing (9) with the identification marks upward. up. Install thrust washer (8) with the three lubrication grooves upward. Also install O-ring seal (7) in the cartridge housing.
Illustration 7 g00593907
Ensure that the seal ring on turbine shaft (6) is fitted correctly in the cartridge housing.
Install the locks and the bolts that hold the back plate assembly in position. Tighten the bolts to a torque of 10.2 1.1 N m (90 10 lb in).
Use the following procedure to install the impeller on the shaft.
Put the impeller on the shaft.
Put a small amount of Tooling (H) on the threads and impeller face that will be under the nut. Note: Do not bend or add stress to the shaft when the nut is loosened or tightened.
Tighten the nut to a torque of 14.1 to 17.0 N m (125 to 150 lb in).
Loosen the nut on the shaft.
Tighten the nut to 3.5 N m (31 lb in).
Tighten the nut for an additional 120 degrees.
Illustration 8 g00770104
Position the cartridge housing in a vise. Check the shaft end play with Tool (F). The end play must be 0.08 to 0.25 mm (0.003 to 0.010 inch). If the shaft end play is not the correct dimension, the inside parts of the center housing must be checked.
Illustration 9 g00593906
Position cartridge assembly (3) in turbine housing (4). Install clamp assembly (5).
Illustration 10 g00593902
Install the turbine housing on Tooling (A). Install the cartridge assembly in position in the turbine housing. Ensure that the markings on the housings are in alignment with each other. Put Tooling (I) on the threads of the clamp (2) which holds the cartridge assembly to the compressor housing (1). Install the clamp (2) and tighten the bolt to a torque of 14 2 N m (10 2 lb ft). End By:
Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
AP500F Asphalt Paver 44900001-UP (MACHINE) POWERED BY C4.4 Engine
AP555F Asphalt Paver 5F500001-UP (MACHINE) POWERED BY C4.4 Engine
AP555F Asphalt Paver M4500001-UP (MACHINE) POWERED BY C4.4 Engine
AP500F Asphalt Paver AF500001-UP (MACHINE) POWERED BY C4.4 Engine


Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.