parts catalog

HOSE AS 5088829 - Caterpillar

5088829 HOSE AS Caterpillar parts HOSE
Alternative (cross code) number:
Caterpillar 5088829 HOSE AS

Buy HOSE AS 5088829 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Illustration 11 g01517429
Use a suitable hammer and a suitable punch in order to stake nut (22).
Illustration 12 g01517383
Install thrust washer (20) and side gear (21). Install gears (19) and thrust washers (18).
Illustration 13 g01517379
Install planetary shafts (17). Install locking pins (16). Install side gear (15) and thrust washer (14). Install cover (13).
Illustration 14 g01041480
Raise the temperature of bearing cone (9) and (10). Install bearing cones (9) and (10).
Illustration 15 g01040825
Install bevel gear (12) onto the differential. Apply Tooling (K) to the threads of bolts (11). Install bolts (11) and tighten bolts (11) to a torque of 105 5 N m (77 4 lb ft).
Illustration 16 g01040808
Install bearing cups (6) and (7) and install the differential into axle housing (8).
Illustration 17 g01040715
Install caps (5) and install bolts (4). Slightly tighten bolts (4). Do not torque bolts (4) at this time.
Illustration 18 g01034579
Use Tooling (A) and install spanner nuts (3).
Oscillate the pinion shaft and use Tooling (A) in order to advance spanner nuts (3) until there is slight backlash and no end play on the bearings.
Illustration 19 g01040894
Use a dial type torque wrench and measure the total rotating torque. Use the following formula in order to calculate the total rotating torque (TRT): P equals the rotating torque that was measured in Step 13. TRT = P + 0.281 N m (2.487 lb in) to P + 0.469 N m (4.147 lb in)
If the total rotating torque (TRT) is less than the specified amount, tighten the spanner nuts. If the total rotating torque (TRT) is greater than the specified amount, loosen the spanner nuts. Be sure to always maintain a slight backlash.
Illustration 20 g01041487
Mount Tooling (L) onto the differential housing, as shown. Measure the backlash between the pinion and the bevel gear. The proper backlash setting is between 0.180 mm (0.0071 inch) and 0.320 mm (0.0126 inch).
Illustration 21 g01029595
If the backlash is not within the specification, retract one spanner nut and advance the opposite spanner nut equally. This will maintain the bearing preload. If the backlash is less than the specified amount, move the bevel gear in Direction (A). If the backlash is greater than the specified amount, move the bevel gear in Direction (B).
Illustration 22 g01040713
Install retainers (2) and bolts (1). Tighten bolts (1) to a torque of 13 N m (115 lb in).
Illustration 23 g01034820
Tighten bolts (4) to a torque of 260 + 13, − 39 N m (192 + 10, − 29 lb ft). End By:
Install the front axle differential and bevel gear into the axle housing. Refer to Disassembly and Assembly, "Axle Housing (Differential and Bevel Gear) (Front) - Install".

Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.