parts catalog

HOSE AS 5088907 - Caterpillar

5088907 HOSE AS Caterpillar parts HOSE
Alternative (cross code) number:
Caterpillar 5088907 HOSE AS

Buy HOSE AS 5088907 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 25
  For full view, you need register


Parts List
Table 1
Required Parts    
Item    Qty    Part Number    Description    
1     1     111-4871     Relay    
2     1     216-5383     Wire As    
3     2     5P-2321     Fork Terminal    
4     4     5P-4571     Blade Terminal    Relay Installation Procedure
Indications That The Relay Needs To Be Installed
The unit is not working.
Connect to the unit using Cat Electronic Technician (Cat ET).
If there is a 556-7 code for a shutdown, clear the code, and monitor Cat ET for injector disabled.As soon as the engine starts then the injector disable should go away. If the injector disable does not go away, then the unit will crank over.
The unit may start and run. Then while running, the injection disable status flag will come on, and unit will either shut down or will start to shut down and then come back up to full RPM.Checking For A Faulty Relay
Illustration 1 g03710698
If you have label tags showing on Cat ET and the engine will keep spinning over but will not start, make an insulated wire jumper. Use the wire to jumper the terminals with wire number 13 and wire number 14 while the unit is turning over. The unit should start.Items Required For External Relay Bypass
Illustration 2 g03711258
111-4871 Relay
2-12 inch wires (16 AWG)
Two RED forked spades of size 16 - 14 AWG
Four BLUE female spades of size 16 - 14 AWGFabricate two jumpers using components from the list above. Each jumper will have a red forked spade lug on one end, and a blue spade lug on the other end. Refer to Illustration 2.
Illustration 3 g03722926
(1) 216-5383 Wire As Installation Procedure
Illustration 4 g03710752
Remove the bottom left lock nut from the EMCP and slide the Relay on and then screw the nut back in place.
Illustration 5 g03710754
Remove wire number 13 and wire number 14 from the top left of the EMCP.
Illustration 6 g03710756
Remove the cable ties that are holding the wire number 13 and wire number 14 in place. Then cut off forked spades (Red) and replace with new blue female spades.
Illustration 7 g03710760
Take the 2-12 inch leads you made and insert the leads on terminal 24 (B+) (fifth from the TOP on the RIGHT) and on terminal 28 (B-) (Top terminal on the RIGHT). Refer to Illustration 7.
Illustration 8 g03715860
Connect Wire 13 (2) to Terminal 30, Wire 14 (3) to Terminal 87, Wire 24 (4) to Terminal 86 (B+), and Wire 28 (5) to Terminal 85 (B-) as shown in Illustration 8.
Illustration 9 g03710763
Note: If a new EMCP has to be installed remove the Blue female spades and attach the red forked spades, then insert the wire number 13 and wire number 14 back into the slots on the new EMCP.

Caterpillar parts catalog:

Caterpillar parts catalog
953K Track-Type Loader LJT00001-UP (MACHINE) POWERED BY C7.1 Engine
953K Track-Type Loader JNR00001-UP (MACHINE) POWERED BY C7.1 Engine

Parts hose Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.