AVSPARE.COM
parts catalog

HOSE AS 9V9328 - Caterpillar



9V9328 HOSE AS Caterpillar parts 227 HOSE
Rating:
41
Alternative (cross code) number:
CA9V9328
9V-9328
9V9328
Caterpillar 9V9328 HOSE AS
Weight: 17 pounds 7 kg.

Buy HOSE AS 9V9328 Caterpillar genuine, new aftermarket tractor parts with delivery
LOGGER,

Compatible equipment models: 9V9328:

LOGGER  227   Caterpillar
Number on catalog scheme: 37
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Tool    Part Number    Part Description    Qty    
A     -     Plastigage     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing in the connecting rod.
Install the lower half of the connecting rod bearing in the connecting rod.Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the connecting rod.
Illustration 1 g00487493
In order to check the connecting rod bearing clearance, put Tool (A) on the connecting rod bearing, as shown.
Put clean engine oil (SAE 30) on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Illustration 2 g00487412
Note: Do not turn the crankshaft when Tool (A) is positioned.
Ensure that connecting rod (3) is in position on the crankshaft. Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3) .
Illustration 3 g00287852
Tighten the connecting rod nuts to a torque of 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Remove the connecting rod cap. Measure Tool (A) on the bearing surface before Tool (A) is removed. The clearance between the connecting rod bearing and a new crankshaft should be 0.076 to 0.168 mm (.0025 to .0066 inch). The clearance between the connecting rod bearing and a used crankshaft should be 0.25 mm (0.01 inch).
Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3). Repeat Step 6 in order to tighten the nuts.
Repeat Steps 1 through 8 for the remaining connecting rod bearings.End By:
Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
227 LOGGER 10W00001-UP (MACHINE) POWERED BY 3208 ENGINE


Parts hose Caterpillar catalog:

5P0763 HOSE
120H, 120H ES, 120H NA, 12G, 12H, 12H NA, 135H, 135H NA, 225, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 235D, 3114, 3116, 3126, 3126B, 320 L, 3208, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325 L,...
5P1442 HOSE
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140B, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, ...
5P0767 HOSE
1090, 1190, 1190T, 120G, 1290T, 1390, 140G, 215, 215B, 215C, 215D, 225, 225D, 227, 229, 2290, 229D, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, 245D, 246D, 2470C, 2484C, 249...
8S9355 HOSE
10, 120, 120G, 130G, 140, 14E, 14G, 153, 16, 163, 16G, 173B, 183B, 225, 227, 235, 245, 446B, 518, 518C, 528, 572G, 583K, 594, 621, 621B, 621R, 623, 623B, 627, 627B, 631C, 631D, 633, 633C, 633D, 633E I...
6N4379 HOSE AS
227, 3304, 3408, 3412, 3412C, 3412D, 3508, 3508C, 3512, 3512B, 3516, 3516B, 3606, 3608, 3612, 3616, C280-16, G3406, PM3412, PR-1000, PR-750B
5N5646 HOSE AS
225, 227, 3406B, 3406C, 3406E, 3412, 3456, 3508, 3512, 3512B, 3516, 3606, 3608, 3612, 3616, 5230, 5230B, 776, 776C, 776D, 777, 777B, 777D, 777F, 784B, 784C, 785, 785B, 785C, 789, 789B, 789C, 793B, 793...
2V8570 HOSE AS
215, 225, 227, 235, 245, 3306C, 3516B, 773B, 775B, PR-450
5P5943 HOSE 27 cm(10.6 in.)
130G, 215, 215B, 215C, 215D, 225, 227, 231D, 235, 235B, 235C, 245, 375, 375 L, 587T, 631D, 815B, 825C, 826C, 914G, 924G, 924GZ, 926, 928G, 936, 936F, 938G, 950B, 950B/950E, 950F, 966D, 966F, 980C, 980...
2G4504 HOSE AS
227, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 641B
5P0202 HOSE
225, 227, 235, 235C, 245, 245B, 320B, 320B FM LL, 320B L, 320C, 322B, 322B L, 325B, 325B L, 330, 330 L, 330B, 330B L, 345B L, 350, 375, 992C, R1700 II, R1700G, R2900, R2900G
8K4037 HOSE ASSEM. 15 in.(3.81 dm)
227, 235, 245, 508, 5110B, 589, 69D, 769D, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 777B, AD40, AD45, AE40, AE40 II, D9N, R1600, R1600G, R1700G
2V8555 HOSE ASSEM.
227, 235, 515, 525, 525B, 535B, 545, 814F, 815F, 816F, 824C, 824G, 824G II, 824H, 825C, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 938F, 950F, 950F II, 960F, 966F, 966F II, 970F, 980C, 980F, 980F...
9D5978 HOSE AS
120G, 12G, 130G, 227
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.