AVSPARE.COM
parts catalog

HOSE AS 9W0197 - Caterpillar



9W0197 HOSE AS Caterpillar parts D8N, D8R, D8R II, D8T HOSE
Rating:
30
Alternative (cross code) number:
CA9W0197
9W-0197
9W0197
Caterpillar 9W0197 HOSE AS
Weight: 3 pounds 1 kg.

Buy HOSE AS 9W0197 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 9W0197:

TRACK-TYPE TRACTOR  D8N   D8R   D8R II   D8T   Caterpillar
Number on catalog scheme: 17
 
  For full view, you need register

Information:

start by:a) remove timing gear cover 1. Check to be sure the No. 1 piston is at top center compression position. Install the timing pin in the flywheel and in the fuel injection pump. Remove bolt and washer (2) from fuel pump drive gear.2. Install two 1/2 in. washers (1) between washer (2) and the sleeve on the fuel pump. Install the bolt and washer in the fuel pump drive gear. 3. Put tooling (A) in position as shown and loosen the fuel pump drive gear.4. Remove tooling (A). Remove the bolt and washers. Remove fuel pump drive gear (3). 5. Remove the bolts and remove plate (4). Remove fuel pump idler gear (5). 6. Remove bearing (6) from fuel pump idler gear with tooling (B). 7. Remove bolts (7). Remove camshaft drive gear (8). 8. Remove the nuts and washers from the three studs (10) that hold the fuel injection pump to the timing gear plate.9. Remove bolts and locks (9). Remove timing gear plate (11).Install Timing Gears And Plate
1. Put a new gasket on the plate. Put timing gear plate (1) in position on the cylinder block. Install the locks and bolts that hold the timing gear plate. Install the nuts and washers that hold the fuel injection pump to the timing gear plate. Cut the gasket even with the bottom of the cylinder block. 2. Install camshaft drive gear (2) with the "V" mark on the camshaft drive gear in alignment with the "V" mark on the crankshaft gear. Install the bolts that hold the camshaft gear in position. 3. Install bearing (3) in the fuel pump idler gear with tooling (A) to a depth of 1.52 mm (.060 in.) below front surface of idler gear.4. Install idler gear (4). Install plate (5) and bolts that hold the gear in position. 5. Put the fuel drive gear (6) in position on the fuel pump. Install the bolt and washer that holds it finger tight only. 6. Install tooling (B) on the fuel pump drive gear as shown. Put a torque of approximately 70 N m (50 lb. ft.) on the fuel pump drive gear in a clockwise direction (as seen from the front of the engine). With the clockwise torque on the pump drive gear, tighten the bolt to a torque of 149 7 N m (110 5 lb. ft.).end by:a) install timing gear cover

Caterpillar parts catalog:

Caterpillar parts catalog
D8N TRACTOR 9TC00001-UP (MACHINE) POWERED BY 3406 ENGINE
D8N TRACTOR / POWER SHIFT / 5TJ00001-UP (MACHINE) POWERED BY 3406 ENGINE
D8T TRACK-TYPE TRACTOR JJ500001-UP (MACHINE) POWERED BY C15 Engine
D8R TRACK-TYPE TRACTOR DWJ00001-UP (MACHINE) POWERED BY C15 Engine
D8R Track-Type Tractor 7XM00001-UP (MACHINE) POWERED BY 3406 Engine
D8R TRACK-TYPE TRACTOR 9EM00001-UP (MACHINE) POWERED BY 3406C Engine
D8R Series II Track-Type Tractor 6YZ00001-UP (MACHINE) POWERED BY 3406E Engine
D8R TRACK-TYPE TRACTOR Differential Steering AKA00001-UP (MACHINE) POWERED BY 3406E Engine
D8T TRACK-TYPE TRACTOR KPZ00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR J8B00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR MLN00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR FCT00001-UP (MACHINE) POWERED BY C15 Engine
D8R TRACK-TYPE TRACTOR RJM00001-UP (MACHINE) POWERED BY 3406C Engine
D8R TRACK-TYPE TRACTOR T5X00001-UP (MACHINE) POWERED BY 3406C Engine
D8T TRACK-TYPE TRACTOR FMC00001-UP (MACHINE) POWERED BY C15 Engine
D8R TRACK-TYPE TRACTOR MEJ00001-UP (MACHINE) POWERED BY 3406C Engine


Parts hose Caterpillar catalog:

5P0742 HOSE (210 CM) ORDER BY THE CM
120G, 215, 215B, 215D, 225, 229, 229D, 235, 235C, 235D, 245, 245B, 307, 307B, 312, 312B L, 312C, 315, 315B L, 315C, 317, 317B LN, 318B, 318C, 320 L, 3208, 320B, 322, 322 LN, 325, 330 FM L, 330 L, 3412...
5P1255 HOSE
120M, 12H NA, 12M, 140H, 140M, 141, 143H, 14H NA, 14M, 160H, 160H ES, 160H NA, 160M, 163H NA, 1673C, 16G, 16H NA, 235B, 245, 245B, 24H, 320B, 330, 330 L, 3304, 3304B, 3306, 3306B, 330B, 330B L, 3406, ...
1226906 HOSE-HYDRAULIC
2590, 521B, 522B, 541, 541 2, 551, 552, 552 2, 627H, 627K, 627K LRC, 631D, 637D, 966F II, AP-1055D, BG-2455D, BG-260D, CB-14B, D8R, PF-300C, PM3508, PM3516, PS-300B
1226872 HOSE-HYDRAULIC
140G, 3516C, 621B, 627F, 631D, 631E, 637D, 777C, 777D, 824C, 824G II, 824H, 824K, 825G II, 825H, 825K, 826G II, 826H, 826K, 834G, 834H, 836G, 836H, 844, 844H, 854G, 854K, 966F II, 980G, 988G, 988H, 99...
4T6224 HOSE AS
D7H, D7R, D7R II, D7R XR, D8N
6Y4061 HOSE AS
D8N, D8R, D8R II
1086981 HOSE AS
D8R, D8R II, D8T
4T6224 HOSE AS
D7H, D7R, D7R II, D7R XR, D8N
7T9004 HOSE AS
D6H, D6H II, D6H XR
7T9005 HOSE AS
D6H, D6H II, D6H XR
3W9861 HOSE AS
CB-54, CB-64, D6H
9W0198 HOSE AS
D8N, D8R, D8R II, D8T
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.