4415982 HYDRAULIC AR Caterpillar parts
SAT322
Rating:
Alternative (cross code) number:
CA4415982
441-5982
4415982
CA4415982
441-5982
4415982
HARVESTER HEAD,
Compatible equipment models: 4415982:
Number on catalog scheme:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 2P-8260 Cylinder Liner Installer 1
C - Loctite LB 8632 Silicone Lubricant -
- Loctite LB 8104 Silicone Lubricant(1) -
- Loctite LB 8801 Silicone Lubricant (2) -
- Loctite LB Superlube (3) -
(1) For use in EAME only
(2) Asia Pacific Division
(3) South America
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Measure liner projection. Refer to Testing and Adjusting, "Cylinder liner projection".
Prepare cylinder liner (2) for installation. There are two types of seals that can be used on the cylinder liners.
Illustration 1 g02130336
Type 1
Illustration 2 g02248239
Type 1
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Dip filler band (3) in clean engine oil. Immediately install filler band (3) onto cylinder liner (2).
Immediately install cylinder liner (2) before filler band (3) can expand.
Illustration 3 g02175641
Type 2
Liner seal (4) requires a machined chamfer at the top edge of the liner bore to install the liner seal.
A chamfer can be machined into the top edge of the bore in the block for the cylinder liner. Refer to Special Instruction, SEBF9203 for the correct procedure for machining the chamfer.Note: Liner seat inserts that include the chamfer are also available. Refer to Reuse and Salvage Guidelines, SEBF8255.
Ensure that the liner groove for liner seal (4) is clean and dry. Install liner seal (4) on cylinder liner (2). Apply a thin coat of Tooling (D) to the cylinder block on the machined chamfer to a distance of 5 mm (0.2 inch) below the machined chamfer. Apply Tooling (C) to liner seal (4).Note: Do not apply Tooling (C) to the liner flange or the top of the cylinder block.
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Illustration 4 g06332785
Use Tooling (B) to press cylinder liner (2) into the cylinder block.
Use a 0.02 mm (0.001 inch) feeler gauge to verify that cylinder liner (2) is against the cylinder block. Check for gaps in multiple places. A gap between the cylinder liner and the cylinder block can indicate a liner seal that is pinched. A liner seal that is pinched will compromise the life of the liner seal and the cylinder head gasket.
Measure liner projection again to ensure that cylinder liner projection is still within specification. Refer to Testing and Adjusting, "Cylinder liner projection". A cylinder liner projection that is no longer within specification can indicate a liner seal that is pinched. A liner seal that is pinched will compromise the life of the liner seal and the cylinder head gasket.
Repeat Step 1 through Step 5 for the remaining cylinder liners.End By:
Install the pistons and the connecting rod assemblies.
Table 1
Required Tools
Tool Part Number Part Description Qty
B 2P-8260 Cylinder Liner Installer 1
C - Loctite LB 8632 Silicone Lubricant -
- Loctite LB 8104 Silicone Lubricant(1) -
- Loctite LB 8801 Silicone Lubricant (2) -
- Loctite LB Superlube (3) -
(1) For use in EAME only
(2) Asia Pacific Division
(3) South America
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Measure liner projection. Refer to Testing and Adjusting, "Cylinder liner projection".
Prepare cylinder liner (2) for installation. There are two types of seals that can be used on the cylinder liners.
Illustration 1 g02130336
Type 1
Illustration 2 g02248239
Type 1
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Dip filler band (3) in clean engine oil. Immediately install filler band (3) onto cylinder liner (2).
Immediately install cylinder liner (2) before filler band (3) can expand.
Illustration 3 g02175641
Type 2
Liner seal (4) requires a machined chamfer at the top edge of the liner bore to install the liner seal.
A chamfer can be machined into the top edge of the bore in the block for the cylinder liner. Refer to Special Instruction, SEBF9203 for the correct procedure for machining the chamfer.Note: Liner seat inserts that include the chamfer are also available. Refer to Reuse and Salvage Guidelines, SEBF8255.
Ensure that the liner groove for liner seal (4) is clean and dry. Install liner seal (4) on cylinder liner (2). Apply a thin coat of Tooling (D) to the cylinder block on the machined chamfer to a distance of 5 mm (0.2 inch) below the machined chamfer. Apply Tooling (C) to liner seal (4).Note: Do not apply Tooling (C) to the liner flange or the top of the cylinder block.
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Illustration 4 g06332785
Use Tooling (B) to press cylinder liner (2) into the cylinder block.
Use a 0.02 mm (0.001 inch) feeler gauge to verify that cylinder liner (2) is against the cylinder block. Check for gaps in multiple places. A gap between the cylinder liner and the cylinder block can indicate a liner seal that is pinched. A liner seal that is pinched will compromise the life of the liner seal and the cylinder head gasket.
Measure liner projection again to ensure that cylinder liner projection is still within specification. Refer to Testing and Adjusting, "Cylinder liner projection". A cylinder liner projection that is no longer within specification can indicate a liner seal that is pinched. A liner seal that is pinched will compromise the life of the liner seal and the cylinder head gasket.
Repeat Step 1 through Step 5 for the remaining cylinder liners.End By:
Install the pistons and the connecting rod assemblies.