parts catalog

INCH HOSE 0000010 - Caterpillar

0000010 INCH HOSE Caterpillar parts D333A, E200B INCH
Alternative (cross code) number:
Caterpillar 0000010 INCH HOSE
Weight: 5 pounds 2 kg.

Buy INCH HOSE 0000010 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 0000010:

MARINE ENGINE  D333A   Caterpillar
Number on catalog scheme: None
  For full view, you need register


Illustration 1 g00418971
Schematic of the Limit Switch (Tilt Lever)
Table 1
Contact     Switch Contact     Wire Number     Switch Status    
Not Activated
(lever not in tiltback) Activated
(lever in tiltback)    
D-19, N/O (1)     N/O     F795-YL     O (2)     R (3)    
D-13, N/C (4)     N/C     F794-BU     R     O    
Return     COM     G939-PK     R     R    
( 1 ) N/O = Normally Open.
( 2 ) O = Open (no continuity to return or ground)
( 3 ) R = Return (continuity to return or ground)
( 4 ) N/C = Normally Closed.This switch has two inputs to the ECM. The two inputs are Normally Open and Normally Closed. During normal operation, one of the inputs is open and the other input is grounded. Table 1 shows the continuity of each switch circuit for the two positions of the switch. When a circuit is measured with a voltmeter, an open circuit will measure approximately 5 VDC and a closed circuit will measure approximately 0 VDC. When both inputs are in the same state, a failure is detected. An FMI 04 is recorded when the status of both inputs are grounded.The possible causes of this diagnostic code are listed below:
The Normally Open circuit (wire F795-YL) is shorted to ground.
The Normally closed circuit (wire F794-BU) is shorted to ground.
The Implement tilt lever switch has failed.
The ECM has failed. This is unlikely.System Response:When this diagnostic code occurs a warning (Category 1) is showing on the monitor. The implement relief pressure is maintained at the lower value of two preset values.Note: Ensure that the CID 0464 FMI 04 is on hold and that the diagnostic code indicator shows "SERV CODE". The diagnostic code will only be present when the tilt lever is in the position which causes both inputs to be closed at the same time. If "SERV CODE" is NOT showing, move the tilt lever to the position that causes "SERV CODE" to show.Test Step 1. CHECK THE NORMALLY CLOSED CIRCUIT FOR PROPER OPERATION.
Turn the key start switch to the OFF position.
Disconnect machine harness connector D from the ECM.
At the machine harness connector D, measure the resistance from contact D-13 (wire F794-BU) to contact D-15 (wire G939-PK). Expected Result:When the lever is NOT in the TILTBACK position, there should be less than 5 ohms of resistance.Results:
OK - The measurement is within an acceptable range. Proceed to test step 3.
NOT OK - The switch or the machine harness has failed. Proceed to test step 2.Test Step 2. CHECK THE NORMALLY CLOSED CIRCUIT OF THE SWITCH.This check determines whether the switch or the machine harness has failed.
Disconnect wire F795-YL and wire F794-BU from the limit switch (tilt lever).
At the switch, measure the resistance between the "N/C" terminal and the common terminal.Expected Result:When the lever is NOT in the TILTBACK position, there should be less than 5 ohms of resistance.Results:
OK - The resistance is within an acceptable range. The machine

Caterpillar parts catalog:

Caterpillar parts catalog
D333 MARINE ENGINE 59B00001-00662

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.