1247435 INSULATION Caterpillar parts D250E, D300E INSULATION
Rating:
Alternative (cross code) number:
CA1247435
124-7435
1247435
CA1247435
124-7435
1247435
Weight: 1 pounds 0 kg.
Buy INSULATION 1247435 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK,
Information:
21. Loosen two hose clamps (34). Remove air inlet hose assembly (35).22. Put identification marks on all wires that are connected to the back side of the alternator for installation purposes. Disconnect wires (31), (29) and ground wire (33) from the back side of the alternator.23. Remove clip (32). Disconnect wiring harness (30). Set the wiring harness to the side.24. Put identification marks on two wires (28) that are connected to the water temperature sending unit for installation purposes. Disconnect the two wires from the sending unit. 25. Close two shutoff valves (36) for the heater. Disconnect hose assemblies (37) from the shutoff valves. 26. Open right rear access door (40). Remove three bolts (38), the washers and cover (39). 27. Remove four bolts (44), the washers and upper plate (42).28. Put identification marks on all hose assemblies that are connected to the main hydraulic pump for installation purposes.29. Disconnect hose assemblies (41) and (43) from the main hydraulic pump. 30. Disconnect five hose assemblies (45) from the main hydraulic pump.31. Remove four bolts (46) and the washers to disconnect pipe assembly (47) from the main hydraulic pump.32. Remove the three bolts and washers that hold lower plate (48) in position. Remove the lower plate. 33. Remove two front engine mounting bolts (49), the washers and the nut support assemblies. Remove the two upper rubber mounts at the front of the engine.34. Remove the two rear engine mounting bolts (49), the washers and the nut support assemblies. Remove the two upper rubber mounts at the rear of the engine. 35. Fasten Tool (A) and a hoist to the lifting brackets on the engine as shown.
Be sure all hose assemblies and wires have been disconnected prior to engine removal.
36. Slowly and carefully remove the engine and main hydraulic pump, as a unit, from the machine. The weight of the unit is approximately 816 kg (1800 lb).37. Remove the four lower rubber mounts for the engine. These mounts may stay on the frame of the machine or in the support mounting brackets. 38. If necessary, remove four bolts (50), the washers and rear engine support mounting bracket (51) from both sides of the engine. 39. If necessary, remove four bolts (52), the washers and front engine support mounting bracket (53) from both sides of the engine. The following steps are for the installation of the engine and main hydraulic pump. 40. Be sure the mating surfaces of the engine and support mounting brackets (51) and (53) are thoroughly clean.41. Install two front engine support mounting brackets (53) and two rear engine support mounting brackets (51).
Visually check the condition of the upper and lower rubber mounts. If the rubber mounts are damaged or appear to be compressed or weak, use new parts for replacement.
42. Install the upper and lower rubber mounts in the front and rear engine support mounting brackets.43. Fasten Tool (A) and a hoist to the lifting bracket on the engine. Slowly and carefully put the engine in position
Be sure all hose assemblies and wires have been disconnected prior to engine removal.
36. Slowly and carefully remove the engine and main hydraulic pump, as a unit, from the machine. The weight of the unit is approximately 816 kg (1800 lb).37. Remove the four lower rubber mounts for the engine. These mounts may stay on the frame of the machine or in the support mounting brackets. 38. If necessary, remove four bolts (50), the washers and rear engine support mounting bracket (51) from both sides of the engine. 39. If necessary, remove four bolts (52), the washers and front engine support mounting bracket (53) from both sides of the engine. The following steps are for the installation of the engine and main hydraulic pump. 40. Be sure the mating surfaces of the engine and support mounting brackets (51) and (53) are thoroughly clean.41. Install two front engine support mounting brackets (53) and two rear engine support mounting brackets (51).
Visually check the condition of the upper and lower rubber mounts. If the rubber mounts are damaged or appear to be compressed or weak, use new parts for replacement.
42. Install the upper and lower rubber mounts in the front and rear engine support mounting brackets.43. Fasten Tool (A) and a hoist to the lifting bracket on the engine. Slowly and carefully put the engine in position
Caterpillar parts catalog:
Parts insulation Caterpillar catalog:
1241522
INSULATION-AIR CONDITIONER
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1195667
INSULATION
D250E, D300E
D250E, D300E
1193805
INSULATION
D250E, D300E
D250E, D300E
1196183
INSULATION
D250E, D300E
D250E, D300E
1193804
INSULATION
D250E, D300E
D250E, D300E
1204110
INSULATION
D250E, D300E
D250E, D300E
1204111
INSULATION
D250E, D300E
D250E, D300E
1204112
INSULATION
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1204113
INSULATION
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1204114
INSULATION
D250E, D300E
D250E, D300E
1238174
INSULATION
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1238175
INSULATION
D250E, D300E
D250E, D300E
1193804
INSULATION
D250E, D300E
D250E, D300E
1196183
INSULATION
D250E, D300E
D250E, D300E
1193805
INSULATION
D250E, D300E
D250E, D300E
1195667
INSULATION
D250E, D300E
D250E, D300E
1241522
INSULATION-AIR CONDITIONER
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1240430
INSULATION-AIR CONDITIONER
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1238174
INSULATION
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1204114
INSULATION
D250E, D300E
D250E, D300E
1204113
INSULATION
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1204112
INSULATION
D250E, D250E II, D300E, D300E II
D250E, D250E II, D300E, D300E II
1204111
INSULATION
D250E, D300E
D250E, D300E
1204110
INSULATION
D250E, D300E
D250E, D300E