AVSPARE.COM
parts catalog

INSULATION AS 4646407 - Caterpillar



4646407 INSULATION AS Caterpillar parts INSULATION
Rating:
11
Alternative (cross code) number:
CA4646407
464-6407
4646407
Caterpillar 4646407 INSULATION AS
Weight: 8 pounds 3 kg.

Buy INSULATION AS 4646407 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 11
 
  For full view, you need register

Information:

Introduction
Do not perform any procedure in this Special Instruction until the information has been read and understood.This Special Instruction describes the rework procedure for adding a dowel pin to the joint between the turbocharger cartridge and turbine housing.Required Parts
Table 1
Part Qty
1A-2036 Dowel 2
243-2975 Clamp As 4
302-6504 Bellows 2
372-5858 Band Clamp 2 Procedure
Note: Apply the following procedure to both turbochargers on the engine. Follow this procedure for replacement or during overhaul for the turbocharger cartridge.
Illustration 1 g03733940
Prior to changing out the clamps, loosen the two bellows that connect to the turbine housing, so that the turbo is isolated and there is no force pulling on the turbine housing.
Illustration 2 g03733942
Verify that the turbo housing is aligned properly. Make sure that the two mating flanges are flush all the way around.Note: If necessary, loosen the turbo cartridge bolts to allow the cartridge to move and align the cartridge flange with the turbo flange.
Illustration 3 g03733945
The housing must be retained although the clamp is off. Use a C-clamp to hold the housing in place.
Install an old V-band clamp to be modified for use as a drill guide.
Illustration 4 g03733946
Illustration 5 g03733947
(A) 15.875 mm (0.625 inch)
(B) 6.5 mm (0.255 inch)
(C) 19 mm (0.75 inch)
Fabricate the drill guide using an old V-band clamp and weld a lead boss to the old V-band clamp. Ensure that this boss is centered on the old V-band clamp.
Illustration 6 g03733948
Cross-section view
(D) 12.5 mm (0.492 inch)
(1) 372-5858 Band Clamp
(2) Turbine housing
(3) Cartridge
Set the drill guide in place for drilling. Drill a hole with a 6.5 mm drill bit to a maximum drill depth of 12.5 mm (0.492 inch).Note: The drilled hole must be centered between the flange halves on the top side of the flanges.
Illustration 7 g03733949
(4) 1A-2036 Dowel
Set dowel pin (4) in place.Note: Pin must be clearance fit, not pressed fit. The dowel should not be over a 0.5 mm (0.020 inch) maximum protrusion.
Illustration 8 g03733950
Illustration 9 g03733952
Once the dowel pin is in place, install the 372-5858 Band Clamp following Engine News, SEBD9761, "A New Band Clamp Is Available for Turbochargers on Certain 3500 and C175-16 Engines".Refer to the Disassembly and Assembly for the engine for the procedure to install the 302-6504 Bellows.

Caterpillar parts catalog:

Caterpillar parts catalog
797F Off-Highway Truck LAJ00001-UP (MACHINE) POWERED BY C175-20 Engine


Parts insulation Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.