AVSPARE.COM
parts catalog

JUMPER-TERMINAL 1C4317 - Caterpillar



1C4317 JUMPER-TERMINAL Caterpillar parts PR-450 JUMPER
Rating:
51
Alternative (cross code) number:
CA1C4317
1C-4317
1C4317
Caterpillar 1C4317 JUMPER-TERMINAL
Weight: 0.010 pounds 0 kg.

Buy JUMPER-TERMINAL 1C4317 Caterpillar genuine, new aftermarket tractor parts with delivery
COLD PLANER,

Compatible equipment models: 1C4317:

COLD PLANER  PR-450   Caterpillar
Number on catalog scheme: 31
  
  For full view, you need register

Information:


Table 5
FMI 5 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check The Solenoid.
A. Turn the key start switch and the disconnect switch to the OFF position.
B. Disconnect the solenoid from the machine harness.
C. At the harness connector for the solenoid, install a jumper wire between contact 1 and contact 2.
D. Turn the key start switch and the disconnect switch to the ON position. Do not start the engine.
The FMI 5 diagnostic code changes to an FMI 6 after the jumper wire is installed. OK - The harness is correct. The FMI 5 diagnostic code changes to an FMI 6 when the jumper wire is installed. The solenoid has failed.
Repair: Replace the solenoid.
Proceed to Test Step 3.
NOT OK - The diagnostic code remains active.
Proceed to Test Step 2.
2. Check The Harness For An Open.
A. Turn the key start switch and the disconnect switch to the OFF position.
B. Disconnect the harness connectors from the ECM.
C. The jumper wire remains installed.
D. At the machine harness connector for the ECM, measure the resistance between the signal circuit and return circuit.
Note: For solenoids that return to ground, measure the resistance between the signal circuit at the ECM harness connector and frame ground.
Each reading is less than 5 Ω. OK - The reading is less than 5 Ω. The harness is correct.
Proceed to Test Step 3.
NOT OK - The reading is greater than 5K Ω. The open is in the signal circuit or the return circuit.
Repair: Repair or replace the machine harness.
Note: A resistance that is greater than 5 Ω but less than 5K Ω indicates a loose or a corroded connection in the circuit. A resistance measurement that is greater than 5K Ω indicates an open in the circuit.
Proceed to Test Step 3.
3. Check If The Diagnostic Code Remains
A. Reconnect all harness connectors. Return machine to normal operating condition.
B. Turn the key start switch and the disconnect switch to the ON position.
C. Clear all diagnostic codes.
D. Operate the machine.
E. Stop the machine and engage the safety lock lever.
F. Check if the diagnostic code is active.
The diagnostic code is no longer present. OK - The diagnostic code does not exist at this time. The initial diagnostic code may have been caused by poor electrical connection or short at one of the harness connections. Resume machine operation.
STOP.
NOT OK - The diagnostic trouble code has not been corrected. If the diagnostic code has not been corrected after performing the procedure a second time, the ECM may require replacement.
Prior to replacing the ECM, always contact the Technical Communicator at your dealership for possible consultation with Caterpillar. This consultation may effect repair time.
Follow the steps in Troubleshooting, "ECM - Replace" if the ECM needs to be replaced.
STOP.
Table 6
FMI 6 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check The Solenoid
A. Turn the key start switch and the disconnect switch to the OFF position.
B. Disconnect the solenoid from the machine harness.
C. Turn the key start switch and the disconnect switch to the ON position. Do not start the engine.
D. Observe the status of the

Caterpillar parts catalog:

Caterpillar parts catalog
PR-450 COLD PLANER 7DC00204-UP (MACHINE) POWERED BY 3408 ENGINE


Parts jumper Caterpillar catalog:

9N9800 JUMPER-TERMINAL
10 FT, 10-20B, 10B, 8 FT, 8-16B, AP-1000B
3050674 JUMPER AS
R1300G, R1300G II
9X8194 JUMPER-STRIP
24H, 5130, 5130B, 5230, 5230B, 785C, 785D, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 797, 797B, 797F, 994, 994D, 994F, 994H
8W4753 JUMPER-PLUG-IN
589, 784B, 785, 785B, 789, 789B, 789C
3310158 JUMPER AS
D10T, D10T2, D11T
1807089 JUMPER-INTERNAL
320C FM, 325B L, 325C, 325C L, 325D MH, 330B L, 330C L, 330C MH, 330D MH, 345B, 345B II, 345B II MH, 345C, 345C MH, 365B, 365B II, 365C L MH, 375 L, 385C L MH, M325B, M325C MH, M325D L MH, M325D MH, M...
1807090 JUMPER-INTERNAL
320C FM, 325B L, 325C, 325C L, 325D MH, 330B L, 330C L, 330C MH, 330D MH, 345B, 345B II, 345B II MH, 345C, 345C MH, 365B, 365B II, 365C L MH, 375 L, 385C L MH, M325B, M325C MH, M325D L MH, M325D MH, M...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.