AVSPARE.COM
parts catalog

KIT-GASKET 3156669 - Caterpillar



3156669 KIT-GASKET Caterpillar parts 140H, 143H, 14H, C-10, C-12 KIT
Rating:
21
Alternative (cross code) number:
CA3156669
315-6669
3156669
Caterpillar 3156669 KIT-GASKET
Weight: 2 pounds 0 kg.

Buy KIT-GASKET 3156669 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER, TRUCK ENGINE,

You can buy parts: .

$213.24

06 Oct 2021
2.0[0.90] Pounds
US: Highway And Heavy Parts
3156669 | Caterpillar Gasket Set, Front Structure
HHP HIGHWAY & HEAVY PARTS HHP provides parts equal or better in quality compared to the OE at a fraction of the cost. || Products are crafted with hard-wearing materials for long-lasting strength and durability. || Parts meet or exceed OEM specifications to ensure proper fit and function. || Image(s) is for illustration purposes only and may not represent the actual part. || Products are only sourced from quality certified manufacturing facilities.
$180.38

08 Dec 2018

CATERPILLAR AFTERMARKET: CATERPILLAR AFTERMARKET
CATERPILLAR KIT-GASKET 3156669 NEW
$118.71

06 Oct 2021
4.6076[2.07] Pounds
US: IronDT
Caterpillar Front Structure Replacement suitable for Caterpillar C-12 Engine Serial Nos. 3PD (3156669) New Aftermarket By CTP
CTP
  For full view, you need register

Compatible equipment models: 3156669:

MOTOR GRADER  140H   143H   14H  
TRUCK ENGINE  C-10   C-12   Caterpillar

Information:

System Operation Description:Most electrical problems are caused by poor connections. The following procedure will assist in detecting problems due to connectors. If a problem is found in an electrical connector, repair the connector and verify that the problem does not return. Do not cut connector wires unless terminals are being replaced. Repair the connectors with a 1U-5804 Crimp Tool. The wedges on the DT connectors are easily removed with a 147-6456 Removal Tool.Intermittent electrical problems often disappear by disconnecting and reconnecting connectors. It is very important to check for diagnostic codes immediately before disconnecting a connector. Also check for diagnostic codes after reconnecting any connectors. If the status of a diagnostic code is changed due to disconnecting and reconnecting a connector, there are several possible reasons. The likely problems are loose or improperly crimped terminals, moisture, corrosion, or connectors not mated securely.ALWAYS crimp the terminals on the wires with the 1U-5804 Crimp Tool. Do not solder the terminals.
Illustration 1 g00675955
Connector receptacles (Deutsch) and connector plugs (Deutsch)
Illustration 2 g00665457
Harness routing and seal plugs
Test Step 1. Check the Locking of the DT Connector (Deutsch) and Check the Lock Ring of the HD Style Connector (Deutsch)
Ensure that the connector is properly locked. Also ensure that the two halves of the connector can not be pulled apart.
Verify that the latch tab of the connector is properly latched. Also verify that the latch tab of the connector returns to the locked position. Expected Result:The connector will securely lock. The connector and the locking mechanism are without cracks or breaks.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connector or replace the connector, as required.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Allen Head Screw on the Connector for the Electronic Control Module (ECM)
Ensure that the allen head screw is properly tightened. Be careful not to overtighten the screw and break the screw.
Do not exceed 2.25 N m (20 lb in) of torque on the allen head screw. Expected Result:The ECM connector is secure and the allen head screw is properly torqued.Results:
OK - Proceed to Test Step 3.
Not OK - Repair: Repair the connector or replace the connector, as required.Verify that the repair eliminates the problem.STOPTest Step 3. Perform a Pull Test on Each Wire Terminal Connection
Each terminal and each connector should easily withstand 45 N (10 lb) of pull and each wire should remain in the connector body. This test checks whether the wire was properly crimped in the terminal and whether the terminal was properly inserted into the connector.
The DT connectors use a green wedge to lock the terminals in place. Ensure that the green wedge is not missing and that the green wedge is installed properly on the DT connectors. Note: Terminals should always be crimped onto the wires by using a crimp tool. Do not solder terminals. Use the 1U-5804 Crimp Tool.Expected Result:Each terminal and each connector easily withstands 45 N (10 lb) of pull and each wire remains in the connector

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts kit Caterpillar catalog:

2G6664 KIT-DIAPHRAGM
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 5130, ...
2350355 KIT-SEAL
14H, 14H NA, 14M, 613C, 613C II, 613G, 914G, IT12B, IT14G, IT14G2
1870424 KIT-REPAIR
14H, 16G, 16H, 16H NA, 518C, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G
2339204 KIT-SEAL
120G, 120H, 120H ES, 120H NA, 120K, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 140M 3, 140M 3 AWD...
1184660 KIT-SEAL
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16H, 16H NA, 24H, 550, 550B, 554, 560B, 570, 570B, 574, 574B, 58...
2341949 KIT-SEAL
14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 924G, 924GZ, 924H, 924HZ, 928H, IT28G
9T9072 KIT-SEAL
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
2G6285 KIT-AIR CONTROL VALVE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
1137916 KIT-SEAL
120G, 12G, 130G, 140G, 14H, 14H NA, 160G
1857688 KIT-SEAL
120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 24H, 24M
6G5874 KIT-COTTER PIN
120G, 130G, 14G, 14H, 14H NA
2422548 KIT-SEAL
14H, 14H NA, 16G, 16H, 16H NA
2266620 KIT-GASKET
C-10, C-12, C13
1857733 KIT-TEMPERATURE SENSOR
3406E, C-10, C-12, C-15, C-16
3206200 KIT-GASKET
345B, 345B II, 345B II MH, 345B L, C-12, W345B II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.