3599754 KIT-ENGINE OVERHAUL Caterpillar parts 3508 KIT
Rating:
Alternative (cross code) number:
CA3599754
359-9754
3599754
CA3599754
359-9754
3599754
Buy KIT-ENGINE OVERHAUL 3599754 Caterpillar genuine, new aftermarket tractor parts with delivery
GEN SET ENGINE,
Compatible equipment models: 3599754:
GEN SET ENGINE 3508
Caterpillar
For full view, you need register
Information:
Ejector Return
When valve spool (6) in control valve (3) is moved to either RETURN position (B), or RETURN, detent position (A), the pump oil goes around the valve spool and through line (4) to the rod end of ejector cylinder (8). (No illustration for this operation.) The pump oil in the rod end of the cylinder moves the piston which pulls the ejector toward its retracted position in the bowl. The piston pushes the oil from the head end of the cylinder through line (1), around valve spool (6) and through line (2) into filter (11) and hydraulic tank (15).
SPRING HOUSING ON CONTROL VALVE
6. Valve spool. 17. Detent balls (four). 18. Kickout valve. 19. Chamber. 20. Retainer. 21. Retainer. 22. Spring.When valve spool (6) is in RETURN, detent position (A), detent balls (17) keep the valve spool in the RETURN, detent position (A), until the moving piston in ejector cylinder (8) is stopped in the head of the cylinder. When the piston stops, there is an increase in the pressure of the pump oil in the circuit to the rod end of the cylinder. The pump oil is also in a passage in valve spool (6). When the increase in the pressure of the pump oil gets to approximately 1600 psi (112.5 kg/cm2) (11040 kPa), the oil opens kickout valve (18) and goes into chamber (19). The chamber is between retainers (20) and (21). The pressure of the pump oil moves retainer (20). Retainer (21) is against spring (22) and is not easy to move. Retainer (20) moves valve spool (6) beyond detent balls (17), and then spring (22) moves valve spool (6) to HOLD position (C).Loosen the screw, that holds kickout valve (18) and the valve spring, when the pressure of the oil which opens kickout valve (18) is too high. Tighten the screw when the pressure of the oil which opens the kickout valve is too low. Earlier control valves have shims between the spring and kickout valve (18) which are used to adjust the pressure setting of the kickout valve.Apron Circuit
SCHEMATIC OF APRON CIRCUIT IN APRON LOWER POSITION
1. Line to head end of apron cylinder. 2. Line to filter and hydraulic tank. 3. Control valve. 4. Passage
When valve spool (6) in control valve (3) is moved to either RETURN position (B), or RETURN, detent position (A), the pump oil goes around the valve spool and through line (4) to the rod end of ejector cylinder (8). (No illustration for this operation.) The pump oil in the rod end of the cylinder moves the piston which pulls the ejector toward its retracted position in the bowl. The piston pushes the oil from the head end of the cylinder through line (1), around valve spool (6) and through line (2) into filter (11) and hydraulic tank (15).
SPRING HOUSING ON CONTROL VALVE
6. Valve spool. 17. Detent balls (four). 18. Kickout valve. 19. Chamber. 20. Retainer. 21. Retainer. 22. Spring.When valve spool (6) is in RETURN, detent position (A), detent balls (17) keep the valve spool in the RETURN, detent position (A), until the moving piston in ejector cylinder (8) is stopped in the head of the cylinder. When the piston stops, there is an increase in the pressure of the pump oil in the circuit to the rod end of the cylinder. The pump oil is also in a passage in valve spool (6). When the increase in the pressure of the pump oil gets to approximately 1600 psi (112.5 kg/cm2) (11040 kPa), the oil opens kickout valve (18) and goes into chamber (19). The chamber is between retainers (20) and (21). The pressure of the pump oil moves retainer (20). Retainer (21) is against spring (22) and is not easy to move. Retainer (20) moves valve spool (6) beyond detent balls (17), and then spring (22) moves valve spool (6) to HOLD position (C).Loosen the screw, that holds kickout valve (18) and the valve spring, when the pressure of the oil which opens kickout valve (18) is too high. Tighten the screw when the pressure of the oil which opens the kickout valve is too low. Earlier control valves have shims between the spring and kickout valve (18) which are used to adjust the pressure setting of the kickout valve.Apron Circuit
SCHEMATIC OF APRON CIRCUIT IN APRON LOWER POSITION
1. Line to head end of apron cylinder. 2. Line to filter and hydraulic tank. 3. Control valve. 4. Passage
Caterpillar SIS machinery equipment:
Caterpillar SIS
- 3508 Generator Set Engine (High Speed) 23Z03489-UP » 359-9754 KIT-ENGINE OVERHAUL
Parts kit Caterpillar catalog:
3056, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 789D, 854G, 992G, 994, 994D, 994...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 5130, 5130B, 776C, 776D, 777, 777B, 777C, 777D, 854G, 992G, D11N, D11R, G3508, G3512, PM3508
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 16...
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 215B,...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 16...
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 215B,...
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 16G, 16H, 16H NA, 2290, 2390, 2391, 245B, 2491, 259...
120M, 12M, 14H, 16G, 16H, 16H NA, 2290, 2390, 2391, 2491, 2590, 3116, 3126, 3126B, 3176, 3176B, 3176C, 3196, 320B, 322B LN, 322C, 324D, 324D L, 324D LN, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 33...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
20R0867
KIT-ENGINE PARTS
3508B
3508B
4305439
KIT-GASKET
12H, 627G, 637G
12H, 627G, 637G
9X6537
KIT-TRANSMISSION BEARING
D7H, D8N
D7H, D8N
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
215D, 219D, 225D, 227, 229D, 231D, 235C, 235D, 3208, 3304, 3306, 3306B, 3406C, 613C, D5E, PS-500
3990700
KIT-OPERATOR PLATFORM
992G, 992K
992G, 992K
3126E, C7
3327128
KIT-GASKET
797B
797B
140H, 14H