AVSPARE.COM
parts catalog

LEVER AS-TILT 2333600 - Caterpillar



2333600 LEVER AS-TILT Caterpillar parts IT62G II, IT62H LEVER
Rating:
12
Alternative (cross code) number:
CA2333600
233-3600
2333600
Caterpillar 2333600 LEVER AS-TILT
Weight: 101 pounds 46 kg.

Buy LEVER AS-TILT 2333600 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER,

Compatible equipment models: 2333600:

INTEGRATED TOOLCARRIER  IT62G II   IT62H   Caterpillar
Number on catalog scheme: 32
 
  For full view, you need register

Information:

Probable Causes
Active codes and logged codes
Electrical connections
Fuel injection
Fuel quality
Proper lubrication
Isolate the source of the noise.
Valve train components
Gear train and lower end components
CrankshaftRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps    Values    Results    
1. Active Codes and Logged Codes
A. Establish communication between Cat® Electronic Technician (ET) and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
   
Codes
   
Result: There are active codes.
Repair: Troubleshoot any active codes before continuing with this procedure.
Result: There are no active codes.
Proceed to Test Step 2.
   
2. Electrical Connections
A. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Check for correct installation of the fuel injector connectors.
   
Connectors
   
Result: There are suspect connectors.
Repair: Repair connectors that are suspect or replace connectors that are suspect.
Perform the "Wiggle Test" on Cat ET.
Result: There are no suspect connectors.
Proceed to Test Step 3.
   
3. Fuel Injection
C13, C15, and C18 Applications
A. Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
B. Access the "Cylinder Cutout Test" in the "Diagnostic Tests" under the "Diagnostics" menu.
C. Perform the "Automatic Cylinder Cutout Test" on Cat ET.
C9.3 Applications
A. Perform the "Fuel System Verification Test" in the "Diagnostic Tests" under the "Diagnostics" menu.
   
Injector Solenoid Test or Fuel System Verification Test
   
Result: The test was successful.
Proceed to Test Step 4.
Result: The test was not successful.
Repair: Diagnose the problem and then repair the problem.
Reset all active codes and clear all logged codes.
Verify that the repair eliminated the problem.
   
4. Fuel Quality
A. Refer to Operation and Maintenance Manual for information on the proper characteristics of the fuel for the engine. If necessary, obtain a fuel analysis in order to confirm that the correct fuel is being used for the engine. Refer to Systems Operation/Testing and Adjusting, "Fuel System Quality Test" for the proper procedure.
   
Fuel
   
Result: The fuel quality is OK.
Proceed to Test Step 5.
Result: The fuel quality is not OK.
Repair: Replace the fuel. Verify that the repair eliminated the problem.
   
5. Proper Lubrication
A. Check for proper lubrication of the valve components. Check for sufficient lubrication between the injector tappets and the rocker arms.
B. Check for blocked oil passages. Oil passages must be clean. Clean any oil passages that are questionable. Refer to the Disassembly and Assembly for additional information.
C. Inspect the engine oil filters for ferrous material.
D. Obtain an S-O-S oil analysis. The analysis will contribute to a better understanding of oil contamination and the origin of the contamination.
   
Lubrication    
Result: The oil passages are not blocked and the engine has proper lubrication.
Proceed to Test Step 6.
Result: The oil passages are blocked or the engine does not have proper lubrication.
Repair: Make the necessary repairs, Verify that the repair eliminated the problem.
   
6. Isolate the Source of the Noise
A. If the source of the

Caterpillar parts catalog:

Caterpillar parts catalog
IT62G II Integrated Toolcarrier AYA00001-UP (MACHINE) POWERED BY 3126B Engine
IT62H Integrated Toolcarrier M5G00001-UP (MACHINE) POWERED BY C7 Engine


Parts lever Caterpillar catalog:

9M7394 LEVER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 16, 160G, 160H, 160H ES, 160H N...
1794682 LEVER
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 312C, 315C, 318C, 319C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 325D FM, 330C FM, 330C L, 3...
1872082 LEVER-CONTROL
554, 564, 574B, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G II, 824H, 824K, 825G II, 825H, 825K, 826G II, 826H, 826K, 834G, 834H, 834K, 836G, 836H, 836K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 92...
8N2622 LEVER
621G, 910E, 910G, 914G, 916, 918F, 924F, 924G, 924GZ, 926, 926A, 928F, 928G, 936, 936F, 938F, 938G, 938G II, 938H, 950 GC, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962...
7I4078 LEVER AS
515, 525, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 844, 844H, 854G, 854K, 950 GC, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962...
1938113 LEVER AS
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 980G II, 980H, IT62G II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.