AVSPARE.COM
parts catalog

LEVER 3598870 - Caterpillar



3598870 LEVER Caterpillar parts LEVER
Rating:
26
Alternative (cross code) number:
CA3598870
359-8870
3598870
Caterpillar 3598870 LEVER

Buy LEVER 3598870 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


ACTION REQUIRED
The coolant tubes must replaced and and spacers must be added under the sea water tubes. Refer to attached rework procedure.
OWNER NOTIFICATION
U.S. and Canadian owners will receive the attached Owner Notification.
SERVICE CLAIM ALLOWANCES
Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
100% 100% 0% 0% 0% 0%
This is a 8.0-hour job
This is an 8.0 hour job:
2 hours for draining and refilling coolant
2 hours for replacing the tubes and installing the spacers
4 hours to remove and replace damaged liners and collars (this includes removing and replacing the heat exchanger).
An additional 2.0 hours may be allowed based on installation, (include details in claims story).
PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE.
COPY OF OWNER NOTIFICATION FOR U.S. AND CANADIAN OWNERS
XYZ Corporation
3240 Arrow Drive
Anywhere, YZ 99999
PRIORITY - PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE COOLANT TUBES AND ADDING SPACERS UNDER THE SEA WATER TUBES ON CERTAIN 3508, 3508B, 3512B, 3516B, AND G3516B MARINE ENGINES WITH FRONT MOUNTED HEAT EXCHANGERS
MODELS INVOLVED - 3508, 3508B, 3512B, 3516B, G3516B Marine Engines
Dear Caterpillar Product Owner:
The coolant tubes must be replaced and spacers must be added under the sea water tubes on the products listed below. The existing tubes can damage the liners and collars on the heat exchanger causing leaks. You will not be charged for the service performed.
Contact your local Caterpillar dealer immediately to schedule this service. The dealer will advise you of the time required to complete this service.
Please refer the dealer to their Service Letter dated 28Jan2008 when scheduling this service.
We regret the inconvenience this may cause you, but urge you to have this service performed as soon as possible to prevent unscheduled downtime.
Caterpillar Inc.
Identification #(s)
Attached to 28Jan2008 Service Letter
Rework Procedure
Drain the coolant as required and then remove the sea water and engine coolant tubes from the backside of the front mounted heat exchanger. Inspect the liners and collars for damage. If the liners and collars need replaced, refer to the removal and installation procedure described in Special Instruction REHS2599 (Cleaning the Engine Mounted Heat Exchanger).
This service letter does not cover cleaning the engine mounted heat exchanger ar repairing damage to the heat exchanger caused by leaks.
Image1.1.1
After damaged liners and collars have been replaced, replace the engine coolant tubes with new tubes and install one spacer between the heat exchanger and each sea water tube.
Certain engines were shipped with washers between the heat exchanger and the sea water tubes to keep the tubes from damaging the liners. The liners and collars on these engines will not need to be replaced. The washers should be discarded when the new tubes and spacers are installed.
Image1.2.1


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.