AVSPARE.COM
parts catalog

LIGHTING GP 1246663 - Caterpillar



1246663 LIGHTING GP Caterpillar parts 65C, 75C, 75D, 85C, 85D LIGHTING
Rating:
41
Alternative (cross code) number:
CA1246663
124-6663
1246663
Caterpillar 1246663 LIGHTING GP

Buy LIGHTING GP 1246663 Caterpillar genuine, new aftermarket tractor parts with delivery
CHALLENGER,

Compatible equipment models: 1246663:

CHALLENGER  65C   75C   75D   85C   85D   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g01051217
Air inlet and exhaust system
(1) Inlet valves
(2) Exhaust valves
(3) Exhaust manifold
(4) Air-to-air Aftercooler
(5) Air inlet
(6) Exhaust outlet
(7) Turbocharger
(8) Inlet manifold The components of the air inlet and exhaust system control the quality of air and the amount of air that is available for combustion. The components of the air inlet and exhaust system are the following components:
Air cleaner
Turbocharger
Aftercooler
Cylinder head
Valves and valve system components
Piston and cylinder
Inlet manifold
Exhaust manifoldNote: The following description of the operation of the air inlet and exhaust system assumes that the engine is developing boost pressure. Inlet air passes through the air cleaner into the air inlet (5) of the turbocharger compressor wheel. The turbocharger (7) will supply more volume of air into the engine. This compressing of the air is referred to as boost. The compressing of air causes the air temperature to rise to about 204 °C (400 °F). As the air flows through the aftercooler (4) the temperature of the compressed air lowers to about 46 °C (115 °F). Cooling of the inlet air causes the air to become more dense. This increases combustion efficiency and this increases horsepower output.From the aftercooler (4), air enters the inlet manifold (8). Air flow from the inlet manifold (8) into the cylinders is controlled by inlet valves (1). There are two inlet valves and two exhaust valves (2) for each cylinder. The inlet valves (1) open at the top center position before the piston moves toward the bottom center position. This is called the inlet stroke. When the inlet valves (1) open, cooled compressed air from the inlet port enters the cylinder. The inlet valves (1) close as the piston reaches the bottom center position. The piston begins to travel back to the top center position on the compression stroke. The air in the cylinder is compressed to a very high temperature. When the piston is near the end of the compression stroke, fuel is injected into the cylinder and mixes with the air. This causes combustion to start in the cylinder. Once combustion starts, the combustion force pushes the piston toward the bottom center position. This is called the power stroke. The exhaust valves (2) open when the piston moves toward the bottom center position and the exhaust gases are pushed through the exhaust port into exhaust manifold (3) as the piston travels toward top center on the exhaust stroke. The exhaust valves (2) close and the cycle starts again. The complete cycle consists of four strokes:
Inlet
Compression
Power
ExhaustExhaust gases from the exhaust manifold (3) enter the turbine side of the turbocharger (7). The exhaust gas temperature causes the turbine wheel in the turbocharger (7) to turn. The turbine wheel is connected to the shaft that drives the compressor wheel. Exhaust gases from the turbine wheel exit the turbocharger (7).Turbocharger
Illustration 2 g01485074
Turbocharger
(9) Air inlet
(10) Compressor housing
(11) Compressor wheel
(12) Bearing
(13) Oil Inlet port
(14) Bearing
(15) Turbine housing
(16) Turbine wheel
(17) Exhaust outlet
(18) Oil outlet port
(19) Exhaust inlet All of the air that enters the engine passes through the turbocharger. All

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lighting Caterpillar catalog:

3311576 LIGHTING GP-FLOOD
324D, 324D L, 324D LN, 329D L, 336D L, 345D L
2480414 LIGHTING GP-ROADING
950H, 962H, 966H, 972H, IT62H
6C1505 LIGHTING GP-2 LAMP
225D, 229, 229D, 231D
8U6316 LIGHTING GP-BOOM
205B, 206B, 211B, 212B
1831901 LIGHTING GP-FLOOD
824G II, 824H, 825G II, 825H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.