AVSPARE.COM
parts catalog

LINE AS-FUEL INJECTION 1247085 - Caterpillar



1247085 LINE AS-FUEL INJECTION Caterpillar parts 651E, 657E, D10N LINE
Rating:
55
Alternative (cross code) number:
CA1247085
124-7085
1247085
Caterpillar 1247085 LINE AS-FUEL INJECTION

Buy LINE AS-FUEL INJECTION 1247085 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR, WHEEL TRACTOR,

Compatible equipment models: 1247085:

TRACK-TYPE TRACTOR  D10N  
WHEEL TRACTOR  651E   657E   Caterpillar
Number on catalog scheme: 2
 
  For full view, you need register

Information:

start by: a) remove cushion hitch hydraulic pump (623 only)1. Let the oil out of the transmission and differential case. Turn the tractor so it is at a right angle to the scraper.2. Disconnect air line (1) for the hold valve for the transmission.3. Disconnect electrical wire (4) from light and remove clamp that holds it to the transmission.4. Disconnect linkage (2) and remove the bolts that hold it to the differential carrier.5. Disconnect two air lines for the valve of the differential lock.6. Disconnect oil lines (3) from transmission.7. Remove eight bolts, bearing cage (5) and shims. Keep the shims flat and clean for installation. Remove drive shaft (6).8. Remove the four bolts that hold the housing (7) to the case for the transfer gears.9. Install a 5/18"-11NC forged eyebolt in the case for the transfer gears.10. Fasten a hoist and tool (A) to the transmission.11. Remove the nuts (8) and washers that hold the transmission and differential.12. Do not remove four bolts (9) that hold the transmission to the differential.
TYPICAL EXAMPLE13. Remove the transmission, transfer gear and differential as a unit. Weight is 3100 lb. (1400 kg).Install Transmission, Transfer Gear And Differential As A Unit
TYPICAL EXAMPLE1. Remove the access cover from the top of the differential case. Loosen lock nut (1) and turn thrust stop (2) on the inside of differential case to give enough clearance for installation of the differential. Put the transmission, transfer gear and differential in position with tool (A) and a hoist. Install the washers and nuts (6) that hold the transmission and differential. Remove tool (A) and the eyebolt.2. Turn thrust stop to give a clearance of .002 .001 in. (0.05 0.03 mm) between thrust stop and bearing cap and tighten locknut. Install the cover on the top of the differential case. Install the four bolts that hold housing (5) to the case for the transfer gears. Install drive shaft (4). If a new gear or new bearings are being installed, it will be necessary to make an adjustment to the end clearance for gear (3).3. Install input gear cage (12) with shims and bolts (11). Measure end clearance with a dial indicator. Add or remove shims to get .008 .002 in. (0.20 0.05 mm) end clearance in gear.4. Connect the oil lines (8) to the transmission. Connect two air lines for valve of the differential lock. Connect linkage (9) and install the bolts that hold it to the differential carrier.5. Connect electrical wire (10) to the light and install the clamp that holds it. Connect air line (7) for transmission hold valve. Fill the transmission and differential case with oil to correct level.end by: a) install cushion hitch hydraulic pump (623 only)Separation Of Transfer Gear From Transmission
start by: a) remove cushion hitch hydraulic pump (623 only)b) remove transmission, transfer gear and differential as a unit1. Install two 5/8"-11NC forged eyebolt in the transfer gear housing (1) and fasten a hoist.2. Remove bolts that fasten transfer gear

Caterpillar parts catalog:

Caterpillar parts catalog
D10N TRACK-TYPE TRACTOR 2YD00001-UP (MACHINE) POWERED BY 3412 ENGINE
772B TRACTOR 64W00300-UP (MACHINE) POWERED BY 3412 ENGINE
657E Tractor PS PP 90Z00001-UP (MACHINE) POWERED BY 3412C Engine
651E Wheel Tractor-Scraper 89Z00001-UP (MACHINE) POWERED BY 3412 Engine
D10N Track-Type Tractor 3SK00001-UP (MACHINE) POWERED BY 3412 Engine


Parts line Caterpillar catalog:

4P7804 LINE AS-FUEL INJECTION
3412, 3412C, 3412D, 651E, 657E, 773B, 775B, 990, 992C, 992D, D10N, PM3412, PR-1000, PR-750B
4P7802 LINE AS-FUEL INJECTION
3412, 3412C, 3412D, 651E, 657E, 773B, 775B, 990, 992C, 992D, D10N, PM3412, PR-1000, PR-750B
7C6309 LINE AS-FUEL INJECTION
3412, 651E, 657E, 992C, PR-750B
8N4207 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
8N4209 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
8N4205 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
8N4201 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
8N4203 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
8N4206 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
8N4212 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
8N4202 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
8N4210 LINE AS-FUEL INJECTION
3412, 651E, 657E, 773B, 992C
1247110 LINE AS-FUEL INJECTION
651E, 657E, 773B, 775B, D10N
1247112 LINE AS-FUEL INJECTION
651E, 657E, 773B, 775B, D10N
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.