AVSPARE.COM
parts catalog

LINES GP-FRONT 2277853 - Caterpillar



2277853 LINES GP-FRONT Caterpillar parts LINES
Rating:
11
Alternative (cross code) number:
CA2277853
227-7853
2277853
Caterpillar 2277853 LINES GP-FRONT

Buy LINES GP-FRONT 2277853 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


SEBF8554-04
November 2002
UNDERCARRIAGE
RECONDITIONING BULLETIN
Track Press Assembly Specification Decals
Summary of Revisions
Page Description
All Revised Format.
Introduction
This Bulletin enables dealers and their customers to benefit from cost reductions made possible through an established parts reusability and salvage program. Every effort has been made to provide the most current and relevant information known to Caterpillar Inc. Since the Company makes ongoing changes and improvements to its products, this Bulletin must be used with the latest technical information available from Caterpillar to ensure such changes and improvements are incorporated where applicable.
For questions or additional information concerning this Bulletin, contact Caterpillar Service Support Division, Dealer Support (309) 675-6585.
An updated Track Assembly Specification Chart is available. The introduction of the H, N, and R Series track-type tractors and other new models created a need for this updated chart. It contains the necessary specifications to properly assemble Sealed and Lubricated Track and Positive Pin Retention Track.
The Track Assembly Specifications Chart Decal, Form No. NEEG2430-01, should be used on all track presses.
1 Serial No. 85J10130-Up
2 Serial No. 85J1-85J10129
The Track Assembly Specification Chart is available to dealers in decal form to attach to their track presses. The track press operators will have readily available to them, track-type, pin projection, bushing projection, and maximum force for each model.
For each brand of track press manufacturer, there is one conversion chart decal available. These chart decals will show maximum assembly force, and the conversion pressure for each model track press. They are adaptable to all models of Centurion, Wolff, O.T.C., Bignozzi and Maruma track presses.
The maximum assembly force listed on these decals have been rounded off to consolidate them. Some pressures were rounded up, others down, and all provide adequate pressure to assemble the track properly. With both decals attached to individual presses, the track press operator has all the information needed to properly assemble the track link assembly.
The following is an example of the manner in which information is extracted.
The track press operator will choose the maximum assembly force for the appropriate model from the track assembly specification decal.
With the corresponding track press decal, the operator will match the maximum assembly force with the track press size to determine the gauge pressure.
Samples of the decals are shown below. Each decal, Centurion Track Press Decal (Form No. NEEG2195), Wolff Track Press Decal (Form No. NEEG2196), O.T.C. Track Press Decal (Form No. NEEG2197), Bignozzi Track Press Decal (Form No. NEEG2198) and Maruma Track Press Decal (Form No. NEEG2199), should be ordered for their respective brand of track press.
1 Track presses with the "WM" designation have had the prefix changed to "MTP"
The decals mentioned are available from Corporate Literature Distribution. They can be ordered on a Literature Order form or via the Dealer Terminal System (DTS) by title and form number.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.