AVSPARE.COM
parts catalog

LINES GP-COUPLER 3156320 - Caterpillar



3156320 LINES GP-COUPLER Caterpillar parts FUSION LINES
Rating:
24
Alternative (cross code) number:
CA3156320
315-6320
3156320
Caterpillar 3156320 LINES GP-COUPLER
Weight: 142 pounds 64 kg.

Buy LINES GP-COUPLER 3156320 Caterpillar genuine, new aftermarket tractor parts with delivery
QUICK COUPLER,

Compatible equipment models: 3156320:

QUICK COUPLER  FUSION   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     138-7574     Link Bracket     2    
B     -     Guide Stud
1/2 - 13 NC by 5 inch     2    Start By:
Remove the rear power take-off (RPTO). Refer to Disassembly and Assembly, "Rear Power Take-Off (RPTO) - Remove".
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01265919
Disconnect hose assemblies (2) from flywheel housing (1) .
Remove bolts (4) and install Tooling (B) .
Attach Tooling (A) and a suitable lifting device to flywheel housing (1) . The weight of flywheel housing (1) is approximately 145 kg (320 lb).
Remove remaining bolts (4) and bolts (3) . Remove flywheel housing (1) and the gasket from the cylinder block.Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     138-7574     Link Bracket     2    
B     -     Guide Stud
1/2 - 13 NC by 5 inch     2    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01265919
Illustration 3 g01146784
Install Tooling (B) in the cylinder block.
Attach Tooling (A) and a suitable lifting device to flywheel housing (1) . The weight of flywheel housing (1) is approximately 145 kg (320 lb).
Position the gasket and flywheel housing (1) on the cylinder block. Install bolts (4) and bolts (3) .
Remove Tooling (B) and install remaining bolts (4) .
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt 1 through Bolt 2 to a torque of 55 10 N m (41 7 lb ft).
In a numerical sequence, tighten Bolt 3 through Bolt 10 to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, tighten Bolt 11 through Bolt 36 to a torque of 47 9 N m (35 7 lb ft).
Connect hose assemblies (2) to flywheel housing (1) .End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Install the rear power take-off. Refer to Disassembly and Assembly, "Rear Power Take-Off (RPTO) - Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.