AVSPARE.COM
parts catalog

LINES GP-COUPLER 3156323 - Caterpillar



3156323 LINES GP-COUPLER Caterpillar parts FUSION LINES
Rating:
27
Alternative (cross code) number:
CA3156323
315-6323
3156323
Caterpillar 3156323 LINES GP-COUPLER

Buy LINES GP-COUPLER 3156323 Caterpillar genuine, new aftermarket tractor parts with delivery
QUICK COUPLER,

Compatible equipment models: 3156323:

QUICK COUPLER  FUSION   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the rear gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Care must be used when removing or installing the camshaft. Do not damage the finished surfaces of the camshaft or the camshaft bearings.
Ensure that the camshaft and camshaft bearings are thoroughly clean. Lubricate the camshaft lobes with a 50/50 mixture of Tooling (D) and clean engine oil. Apply a thin coat of clean engine oil on the camshaft bearings.
Illustration 1 g01160265
Install Tooling (A) and Tooling (B) on the rear of camshaft (15). Install Tooling (A) on the front of camshaft (15).
Install Tooling (C) on the front housing or the rear housing. Tooling (C) is used to support the camshaft.
Use two people to install the camshaft. Use Tooling (C) to assist in aligning the camshaft with the camshaft bearings. Carefully slide the camshaft into the cylinder head. Keep the camshaft level while the camshaft is being installed in the cylinder head. The weight of the camshaft is approximately 35 kg (77 lb).Note: Rotate the camshaft during installation. This will prevent the camshaft from binding in the camshaft bearings.
Remove Tooling (A) and Tooling (B) from the camshaft.
Illustration 2 g01160261
Install sealing plate (13) and adapter assembly (14). Install bolts (12).
Illustration 3 g01160259
Illustration 4 g01151441
Install damper (11) and bolts (10).
Tighten the bolts to a torque of 240 40 N m (177 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.
Illustration 5 g01265946
Install cover (8) and elbow (9).
Illustration 6 g01148835
Install new O-ring seals and sealing plate (7).Note: Ensure that the O-ring seals remain in position on sealing plate (7) during installation.
Illustration 7 g01148238
Install adapter assembly (6), thrust plate (5), and bolts (4).
Illustration 8 g01148237
Illustration 9 g01151468
Reposition gear (3). Install bolts (2).
Tighten the bolts to a torque of 240 40 N m (177 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.
Illustration 10 g01265926
Install cover (1).
Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".End By:
Install the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, "Rocker Arms and Shaft - Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.