AVSPARE.COM
parts catalog

LINES GP-COUPLER 3156344 - Caterpillar



3156344 LINES GP-COUPLER Caterpillar parts FUSION LINES
Rating:
13
Alternative (cross code) number:
CA3156344
315-6344
3156344
Caterpillar 3156344 LINES GP-COUPLER

Buy LINES GP-COUPLER 3156344 Caterpillar genuine, new aftermarket tractor parts with delivery
QUICK COUPLER,

Compatible equipment models: 3156344:

QUICK COUPLER  FUSION   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Specifications
Table 1
Fan Speed Calibration Speed
Model Minimum Speed Maximum Speed
924K
930K 700 50 rpm 1500 25 rpm
938K 700 50 rpm 1550 25 rpm Required Tools
Table 2
Required Tools
Part Number Description Quantity
1U-6605 Reflective Tape 1
9U-7400 Multitach Tool Group 1
JEBD3003 Caterpillar Electronic Technician (ET) 1
317-7484 Communication Adapter Gp 1 Preparation for Calibration
Move the machine to a smooth, horizontal location. Move the machine away from other operating machines and away from personnel. Place the transmission direction and speed control lever in the NEUTRAL position. Stop the engine.
Engage the parking brake. Lower the work tool to the ground. Put blocks in front of the wheels and behind the wheels.
Inspect the hoses for the fan drive for damage. Inspect all of the connectors for the fan drive for damage. Inspect all of the components for the fan drive for damage.
Illustration 1 g02828437
Location of the reflective tape
Note: If there is already a piece of reflective tape on the fan blade, then continue from step 7.
Remove grill assembly.
Attach 1U-6605 Reflective Tape (1) to the fan.
Install the grill assembly.
Install the 9U-7400 Multitach Tool Group on the grill assembly.
Start the engine and run the engine at low idle. Note: In order to ensure proper operation of the cooling system, the doors for the engine enclosure should be closed while the test procedures are conducted.
The software program that will be used for this test procedure is the Caterpillar Electronic Technician (ET). The Caterpillar Electronic Technician is a software program that can be used on an IBM-compatible personal computer. Refer to the Service Manual, JEBD3003 for the requirements in order to install ET.
Open the software program (ET) and check for active diagnostic codes. If there is an active diagnostic code, the calibration procedure will be stopped until the condition that caused the diagnostic code is corrected.
Once any active diagnostic codes are corrected, select the engine ECM from the available ECM list.
Follow the prompts on the display in order to complete the procedure. Note: Record fan speeds during testing and compare to values in the specification table. Refer to Table 1.
Illustration 2 g01407721
Illustration 3 g02828498
Illustration 4 g02828536
Illustration 5 g02828576
Illustration 6 g02828579
Illustration 7 g02828596
Illustration 8 g02828638

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lines Caterpillar catalog:

8X0268 LINES GP-HEATER
793, 793B, 793C, 793D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.