AVSPARE.COM
parts catalog

LINES GP-AIR COMPRESSOR 3535057 - Caterpillar



3535057 LINES GP-AIR COMPRESSOR Caterpillar parts C15, C18, CX31-C18I, CX35-C18I LINES
Rating:
64
Alternative (cross code) number:
CA3535057
353-5057
3535057
Caterpillar 3535057 LINES GP-AIR COMPRESSOR

Buy LINES GP-AIR COMPRESSOR 3535057 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE, PETROLEUM PACKAGE,

Compatible equipment models: 3535057:

INDUSTRIAL ENGINE  C15   C18  
PETROLEUM ENGINE  C15   C18  
PETROLEUM PACKAGE  CX31-C18I   CX35-C18I   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Oil Filter Inspection
Inspect Used Filter for Debris
Element with debris.Use a 4C5084 Filter Cutter (formerly 6V7905) to cut the filter element open. Spread pleats apart and inspect the element metal and other debris. An excessive amount of debris in the filter element can indicate a possible failure.Use a magnet to differentiate between ferrous and non-ferrous metals found in the filter element.Ferrous metals can indicate wear on the steel and cast iron parts.Non-ferrous metals can indicate wear on the aluminum parts of the engine, such as main, rod and/or turbocharger bearings.Due to normal wear and friction, it is not uncommon to find small amounts of debris in the filter element. Consult your Caterpillar dealer to arrange for further analysis if an excessive amount of debris is found.Use of an oil filter element not recommended by Caterpillar can result in severe engine damage to engine bearings, crankshaft, and other parts. This can result in larger particles in unfiltered oil entering the lubricating system and causing damage.Bucket Clearance (If Equipped with a Bucket Capable of Shim Adjustment)
Inspect/Adjust
When performing this adjustment, put the hydraulic activation control lever in the LOCKED position and stop the engine.
Improperly adjusted bucket clearance could cause galling on the contact surfaces of the bucket and stick, resulting in excessive noise and/or damaged O-ring seals.
(1) No Gap. (2) Stick Boss. (3) Bucket Clearance. (4) Shim Group. (5) Pin. (6) Plate. (7) Bolts. (8) Washers. (9) Location. (10) Flange. (11) Bucket Boss.The bucket linkage clearance of this machine can be adjusted by shimming. If the bucket-to-stick gap becomes excessive, adjust to the specification shown below. Two different size shims of 0.5 mm (.02 in) and 1.0 mm (.04 in) thicknesses are used at location (9).
Bucket linkage adjustment area.1. Position the machine on a level surface and lower the bucket to the ground.2. Slowly operate the swing control lever until the stick boss (2) and left bucket boss (11) are in full face to face contact (no gap) (1). This is to help determine the total clearance of the stick-to-bucket connection.3. Place the hydraulic activation control lever in the LOCKED position and stop the engine.4. Measure distance (3) which is the existing total clearance.5. Determine the shim thickness that needs to be removed from shim group (4) by performing the following calculation. Thickness of shims to be removed:Total clearance (3) - [0.5 to 1.0 mm (.02 to .04 in)] = thickness of shims to be removed6. Remove the appropriate number of shims to meet the above calculation. Be sure to use a minimum of three 0.5 mm (.02 in) shims. To remove shims, remove bolts (7), washers (8), and plate (6).7. After the correct number of shims have been removed, install plate (6), washers (8), and bolts (7) with pin (5) aligned with pin hole. Tighten bolts (7) to a torque of 240 40 N m (180 30 lb ft).8. After installation, make sure that clearance (3) is still correct.Cab Air Filter
Clean
The filter is located on the left side of

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
C15 Petroleum Engine MG200001-UP
C18 Petroleum Engine BE200001-UP


Parts lines Caterpillar catalog:

2916821 LINES GP-ENGINE OIL
631E, 631G, 633E II, 637E, 637G, 657E, 657G, 834H, 834K, 836H, 836K, 988H, 988K, AD45B, AD55, C15, C18, CX31-C15I, CX31-C18I, CX35-C18I, CX35-P800, PM-200, PM-201, TH35-C15I
3672670 LINES GP-FUEL
C15, C18, CX31-C18I, CX35-C18I
3476003 LINES GP-OIL
C15, C18, CX31-C18I
3600767 LINES GP-EXHAUST
C18, CX31-C18I, CX35-C18I
3534981 LINES GP-AIR COMPRESSOR
C15, C18, CX31-C18I, CX35-C18I
3367594 LINES GP-AIR
C18, CX31-C18I, CX35-C18I
3616095 LINES GP-WATER
C18, CX31-C18I, CX35-C18I
3437225 LINES GP-WATER
C15, C18, CX31-C18I, CX35-C18I
3529351 LINES GP-TURBOCHARGER OIL
C15, C18, CX31-C18I, CX35-C18I
3545935 LINES GP-ENGINE OIL
735B, 740B, C15, C18, CX31-C18I, CX35-C18I, D8T
3522911 LINES GP-ENGINE OIL
C13, C15, C18, C9.3, CX31-C13I, CX31-C18I, CX35-C18I
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.