AVSPARE.COM
parts catalog

LINES GP-FRONT 3598583 - Caterpillar



3598583 LINES GP-FRONT Caterpillar parts 314E CR, 314E LCR LINES
Rating:
26
Alternative (cross code) number:
CA3598583
359-8583
3598583
Caterpillar 3598583 LINES GP-FRONT

Buy LINES GP-FRONT 3598583 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3598583:

EXCAVATOR  314E CR   314E LCR   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

3. Handle all parts with care to avoid nicking critical areas. File smooth any parts, other than the sealing faces, that have nicks that may make assembly difficult or questionable.4. Wash off all dirt accumulation from used parts. It may be necessary to use a wire brush to clean the accumulations of dirt or rust from the bore of the seal retainers to assure they are clean and smooth.5. Remove all oil or the protective coating from floating ring seals (2) and from retainers (4) with a nonflammable cleaning solvent and dry them.6. Be sure the ramps on the retainers and on the floating ring seal are dry and with no oil present. Check the ramps for rough tool marks and nicks. On used parts, remove all dirt or rust deposits from the ramps with a scraper or wire brush, and smooth the surface with emery cloth.7. Always install new rubber toric sealing rings (1) on floating ring seals (2). Never install a used toric sealing ring on a new or used floating ring seal.8. Install toric sealing ring (1) on floating ring seals (2). Be sure the toric sealing ring is not twisted and that it sets straight and against the lip that keeps it from falling off the floating ring seal. See Fig. A and Fig. C.
Use caution when using Trichlorethane. Follow the manufacturer's recommendations on the container when using Trichlorethane.
9. Before installation of the Duo-Cone floating seals, wet the toric sealing ring in Trichlorethane so it will slip easily under the housing retainer lip. Do not use stanisol or any other liquid that leaves an oily film or does not evaporate quickly. 10. Use correct tooling to install Duo-Cone floating seals. Duo-Cone floating seal installation tools are available for various size seals. See the Power Train Tools section of the Tool Guide for a list of installation tools. A typical installation tool is shown in the illustration.
If the installer tool is not used, do not use a screwdriver or stick to assemble the toric sealing ring in the retainer. Use finger pressure only.
11. Install the Duo-Cone floating seal in retainer (4) until the toric sealing ring is under the lip of the retainer. Make sure toric sealing ring does not twist when installed. This can cause floating seal ring (2) to cock. See Figure B.12. After assembly, check dimension (X) (see fig. C) four places 90° apart. Height variation around the assembled ring should not exceed 1.0 mm (.040 in.). Use the Duo-Cone floating seal installation tool to make any adjustments. Do not push directly on the floating seal ring.13. Before assembling floating ring seals together wait at least two minutes to let all isopropyl alcohol evaporate.14. Wipe the faces of the seals with a lint free tissue to remove any foreign material.15. Put a thin film of clean oil on the seal faces. Be careful not to let any oil come in contact with the toric sealing ring or its mating surface.16. Carefully bring

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
314F Excavator RAF00001-UP (MACHINE) POWERED BY C4.4 Engine
314E CR/SR & 314E LCR Excavators ECN00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts lines Caterpillar catalog:

3473726 LINES GP-COUPLER
311D LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR, 314E LCR, PIN GRAB
1797600 LINES GP-STICK
312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
4184030 LINES GP-EXHAUST COMBUSTION
336F L, 627K, 725C, 966M, 966M XE, 972M, 972M XE, C9.3
7I5016 LINES GP-AIR CONDITIONER
143H, 160H ES, 160H NA, 163H NA
1480169 LINES GP-PROTECTION
3612, 3616, C280-12, C280-16
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.