AVSPARE.COM
parts catalog

LINES GP-AUXILIARY HYDRAULIC 3598837 - Caterpillar



3598837 LINES GP-AUXILIARY HYDRAULIC Caterpillar parts 324E LN LINES
Rating:
68
Alternative (cross code) number:
CA3598837
359-8837
3598837
Caterpillar 3598837 LINES GP-AUXILIARY HYDRAULIC

Buy LINES GP-AUXILIARY HYDRAULIC 3598837 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3598837:

EXCAVATOR  324E LN   Caterpillar
  For full view, you need register

Information:


Illustration 1 g03170476
Connectors of "Steer Position Sensor 1"
Three "steer position sensors" are required for correct operation of the steering control lever. The "steer position sensors" are located in the assembly of the left joystick . Each sensor provides an input signal to the Implement ECM and to the Transmission/Chassis ECM. This diagnostic code is activated when the ECM detects that the signal voltage from the "steer position sensor 1" is below normal. The "steer position sensor 1" receives power from the 8V power supply of the Implement ECM. "Steer position sensor 1" is internally connected to the ground that is supplied by the 8V sensor return of the Transmission/Chassis ECM and to the Implement ECM (ECM ground). The "steer sensor" must lose both grounds in order to lose a ground connection. The illustration above indicates the power and ground connections for the "steer sensor 1".Note: For a schematic of the internal power and ground assignments for each individual component in the left joystick, refer to the Systems Operation, "Features" section of this manual.The position sensor is a PWM sensor that operates at a frequency of 500 100 Hz. The position sensor sends a PWM input signal to the Implement ECM and to the Transmission/Chassis ECM. The duty cycle of the signal will vary from approximately 10 5% at the joystick full left position to approximately 90 5% at the joystick full right position. When the joystick is in the center position, the duty cycle will be approximately 50%.The possible causes of this diagnostic code are listed below:
The signal circuit is shorted to a ground source.
The sensor has failed.
The ECM has failed. This is unlikely.Note: The Transmission/Chassis ECM (MID 027) and the Implement ECM (MID 082) receive an input signal from the "steer sensor 1". Both ECM modules can activate a CID 1471 FMI 04 diagnostic code when the signal voltage is below normal. If one ECM has activated a CID 1471 FMI 04 diagnostic code and the other ECM has not, it is likely that the sensor is operating correctly. When this occurs, a poor connection in the machine harness would be suspected. When both ECM modules have activated the diagnostic code, either the sensor OR a harness problem could be the cause. If both ECM modules have activated the diagnostic code, it is very unlikely that either ECM is causing the problem. For either condition, proceed with this procedure in order to verify the cause of the problem.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, that all connections are secure and that all connections are in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
326F L & 326F LN Excavators GGJ00001-UP (MACHINE) POWERED BY C7.1 Engine
324E L & 324E LN Excavators LDG00001-UP (MACHINE) POWERED BY C7.1 Engine
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts lines Caterpillar catalog:

3406703 LINES GP-AIR CONDITIONER
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
3454146 LINES GP-FUEL INJECTION
120M 2, 2384C, 2484C, 2570C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 563C, 573C, 579C, 924K, 930K, 938K, 95...
3402967 LINES GP-BOOM
324E, 324E L, 324E LN
3402880 LINES GP-HYDRAULIC
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
2426494 LINES GP-COUPLER
320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D L, 329D, 329D L
3766887 LINES GP-FUEL
2384C, 2484C, 2570C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 563C, 573C, 579C, 950K, 962K, C6.6, C7.1
3761764 LINES GP-GREASE
324E, 324E L, 324E LN
3598363 LINES GP-PILOT
320E L, 320E LN, 323E L, 324E L, 324E LN, 329E, 329E L, 329E LN
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.