AVSPARE.COM
parts catalog

LINES GP-CONNECTING 3599947 - Caterpillar



3599947 LINES GP-CONNECTING Caterpillar parts 307C, 308C, CVP16 LINES
Rating:
80
Alternative (cross code) number:
CA3599947
359-9947
3599947
Caterpillar 3599947 LINES GP-CONNECTING

Buy LINES GP-CONNECTING 3599947 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR, VIBRATORY COMPACTOR,

Compatible equipment models: 3599947:

MINI HYD EXCAVATOR  307C   308C  
VIBRATORY COMPACTOR  CVP16   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g00547445
Illustration 2 g00547519
(A) Torque for 1/4 inch locknuts (jam nuts) on cable assemblies that hold the rod ends in place ... 8 2 N m (6 1.5 lb ft) (B) Torque for 3/8 inch locknut (jam nut) that holds the swivel end on the center rod ... 30 7 N m (22 5 lb ft) (C) Torque for all 5/8 inch jam nuts on cable assembly ... 38 7 N m (28 5 lb ft) (D) Torque for screws that fasten neutral start (9) and backup alarm switch (11) to the plates ... 0.50 0.05 N m (4 .4 lb in) (4) Torque for four screws ... 8 2 N m (6 1.5 lb ft) (7) Torque for nut ... 8 2 N m (6 1.5 lb ft) (10) Torque for screw ... 25 6 N m (18 4.5 lb ft) (11) Dimension (two places) ... 15 2 mm (0.59 0.08 inch) (12) Install the green wire that is marked with the number "306" to the post (COM) on the switch assembly. Install the orange wire that is marked with the number "306" to the open post (NO). (13) Dimension ... 16 2 mm (.63 .08 inch) (14) Install the brown wire that is marked with the number "321" to the post (COM) on the switch assembly. (14) Install the black wire that is marked with the number "200" to the open post (NO) on the switch assembly. (15) 5N-6096 Spring Length under test force ... 25.50 mm (1.004 inch) Test force ... 19.57 N (4.40 lb) Free length after test ... 48.77 mm (1.920 inch) Outside diameter ... 13.82 mm (0.544 inch) (16) 6Y-2846 Spring Length under test force ... 74.64 mm (2.939 inch) Test force ... 626 N (140.8 lb) Free length after test ... 79.92 mm (3.146 inch) Outside diameter ... 20 mm (.8 inch) (17) Dimension (two places) ... 16 2 mm (.63 .08 inch) (18) Torque for three screws ... 1.7 0.25 N m (15.04 2.212 lb in) (19) Torque for two screws ... 0.8 0.1 N m (7.08 .88 lb in) (20) Installation of bearing (depth) ... 4.5 1.0 mm (.18 .04 inch) (21) Ring (22) Torque for three screws ... 8 2 N m (6 1.5 lb ft) (23) Torque for the bolt ... 1.7 0.25 N m (15.04 2.212 lb in) (24) Installation of bearing (depth) ... 1.5 1.0 mm (.06 .04 inch)Procedure for Adjustment of Speed Control
Rotate collar (23) until the number "2" is 30 1 degrees counterclockwise from vertical. This rotation is viewed from the end of handle (2) .Tighten the bolt that holds collar (23) to the specified torque.
Remove plate (5). Rotate lever (9). The lever should be parallel with the top of housing (8) .Install handle assembly (3) with the white mark

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.