AVSPARE.COM
parts catalog

LINES GP-DEF 4645545 - Caterpillar



4645545 LINES GP-DEF Caterpillar parts LINES
Rating:
86
Alternative (cross code) number:
CA4645545
464-5545
4645545
Caterpillar 4645545 LINES GP-DEF

Buy LINES GP-DEF 4645545 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g01079534
Schematic for the 5 V supplyCID 262 FMI 03 service code is recorded when the ECM reads the voltage of the sensor supply circuit (wire L730-OR) as higher than the normal voltage.The following causes could signal this diagnostic code:
The sensor supply circuit (wire L730-OR) is shorted to the +battery circuit.
A sensor has failed.
The ECM has failed. This is unlikely.Note: Ensure that the CID 262 FMI 03 is active.System Response:When this diagnostic code is active the hydraulic control system will default to the "Auto Not Allowed" state.Test Step 1. CHECK FOR THE CORRECT VOLTAGE AT THE ECM.
Turn the disconnect switch and the key start switch to the ON position.
Check the voltage at the connector of the ECM from contact J1-11 (sensor supply) to contact J1-21 (ground). Use the 7X-1710 Cable probes to measure the voltage. Do NOT disconnect the machine harness from the ECM.Expected Result:The voltage is 5.0 0.5 DCV.Results:
OK - Voltage is 5.0 0.5 DCV. The sensor supply voltage is correct. Verify that the diagnostic code is present. If the diagnostic code is still present, the ECM has failed. Replace the ECM.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. Also, recheck if the diagnostic code is active. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Module - Replace".STOP
NOT OK - Voltage is greater than 5.0 0.5 DCV. The sensor supply voltage is NOT correct. Proceed to test step 2.Test Step 2. CHECK THE HARNESS FOR A SHORT TO THE +BATTERY CIRCUIT.
The disconnect switch and the key start switch remain in the ON position.
Disconnect the machine harness from the ECM.
At the machine harness connector for the ECM, measure the voltage from connector contact J1-11 (sensor supply) to frame ground.Expected Result:The voltage is 0.0 0.5 DCV.Results:
OK - The voltage is 0.0 0.5 DCV. The voltage is correct. The ECM has failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. Also, recheck if the diagnostic code is active. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Module - Replace".STOP
NOT OK - Voltage is NOT 0.0 0.5 DCV. The harness has failed.Repair: The machine harness is shorted to the +battery circuit. Repair the machine harness or replace the machine harness.STOP

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
D6T Track-Type Tractor XL, XW, LGP HNK00001-UP (MACHINE) POWERED BY C9.3 Engine
D6 Track-Type Tractor GZ900001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor, XL VPAT, XW VPAT, LGP VPAT KTW00001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor XL VPAT, XE; XW VPAT, XE; LGP VPAT, XE D5M00001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor XL VPAT, XW VPAT, LGP VPAT AG900001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE HFE00001-UP (MACHINE) POWERED BY C9.3 Engine
D6 Track-Type Tractor LRG00001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE B7200001-UP (MACHINE) POWERED BY C9.3 Engine


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.