AVSPARE.COM
parts catalog

LINES GP-WATER 4645742 - Caterpillar



4645742 LINES GP-WATER Caterpillar parts LINES
Rating:
21
Alternative (cross code) number:
CA4645742
464-5742
4645742
Caterpillar 4645742 LINES GP-WATER

Buy LINES GP-WATER 4645742 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

Which Generate This Code:This diagnostic code is recorded when the Implement Control ECM reads the electrical system voltage that is at contact J1-1 as being below normal range (less than 18 volts for two seconds).The possible causes of this diagnostic code are listed:
A charging system component has failed.
The wire harness has failed.
The ECM has failed. This is unlikely.System Response:When this diagnostic code is active, the control system will default to the "Auto Not Allowed" state.Test Step 1. CHECK FOR AN ACTIVE DIAGNOSTIC CODE
Start the engine.
Run the engine at high idle.
View the status of the diagnostic code.Expected Result:The diagnostic code is NOT active.Results:
YES - The diagnostic code is NOT active. The problem does not exist at this time. Watch for a recurrence.STOP
NO - The diagnostic code is active. Proceed to Test Step 2.Test Step 2. CHECK THE BATTERY VOLTAGE.
Measure the voltage at the battery posts.Expected Result:The voltage is greater than 23 volts.Results:
YES - The voltage is greater than 23 DCV. Proceed to Test Step 3.
NO - The voltage is less than 23 DCV.Repair: The charging system is not correct. Check the charging system. See Special Instruction, REHS0354, "Charging System Troubleshooting". STOPTest Step 3. CHECK THE SYSTEM VOLTAGE AT THE ECM
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness connector from the Implement ECM.
Turn the disconnect switch and the key start switch to the ON position.
Run the engine at high idle.
At the machine harness connector for the ECM, measure the voltage between contact 1 and contact 2.Expected Result:The voltage is greater than 18 DCV.Results:
YES - The voltage is greater 18 DCV. This should not cause the diagnostic code. Repair: Inspect the connector. Connect the machine harness to the ECM. Check all connectors in the wire harness. If the CID 0168 FMI 04 remains active, replace the Implement Control ECM. See Testing and Adjusting, "Module - Replace".STOP
NO - The voltage is less than 18 DCV. The machine harness has failed.Repair: Check the +battery circuit and the ground circuit in the machine harness. Repair the machine harness or replace the machine harness. STOP

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
D6T Track-Type Tractor XL VPAT, XE; XW VPAT, XE; LGP VPAT, XE D5M00001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE HFE00001-UP (MACHINE) POWERED BY C9.3 Engine
D6 Track-Type Tractor LRG00001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE B7200001-UP (MACHINE) POWERED BY C9.3 Engine


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.