AVSPARE.COM
parts catalog

LINES GP-INSTR 4645977 - Caterpillar



4645977 LINES GP-INSTR Caterpillar parts LINES
Rating:
21
Alternative (cross code) number:
CA4645977
464-5977
4645977
Caterpillar 4645977 LINES GP-INSTR

Buy LINES GP-INSTR 4645977 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01173065
This diagnostic code is shown when the display reads the voltage of the circuit as being below normal.Note: This condition may occur on start-up of the machine.System Response:When this diagnostic code occurs, low voltage is observed at the display.Test Step 1. VERIFY THAT THE DIAGNOSTIC CODE IS ACTIVEPress the "OK" Key on the display in order to acknowledge the error and clear the error from the screen.Expected Result:Diagnostic code "CB 11" is no longer active.Results:
YES - Diagnostic code "CB 11" is no longer active. Cranking the engine at start-up may have caused the code to be generated.STOP
NO - Diagnostic code "CB 11" is still active. Proceed to test step 2.Test Step 2. CHECK THE WIRE HARNESS
Turn the key start switch for the machine to the "OFF" position.
Disconnect the wire harness from the display at connector "AR-C1".
Install a jumper wire between pin "5" and pin "6" on the harness connector.
Turn the key start switch for the machine to the ON position.
Measure the voltage between pin "1" and pin "6" on the wire harness.Expected Result:The voltage that was measured between pin "1" and pin "6" is machine voltage.Results:
YES - Voltage that was measured between pin "1" and pin "6" is machine voltage. Proceed to test step 3.
NO - Voltage that was measured between pin "1" and pin "6" is not machine voltage. Proceed to test step 4.Test Step 3. CHECK THE DISPLAY
Turn the key start switch for the machine to the ON position.
Measure the resistance between pin "1" and pin "5" on the connector that is located on the "display".Expected Result:The resistance measurement between pin "1" and pin "5" is less than 5 Ohms.Results:
YES - The resistance measurement between pin "1" and pin "5" is less than 5 Ohms. Proceed to test step 4.
NO - The resistance measurement between pin "1" and pin "5" is greater than 5000 Ohms.Repair: The display is faulty. Replace the display.STOPTest Step 4. CHECK THE POWER SUPPLY MODULE
Access the power module. Disconnect the "8 pin" connector from the main harness of the power module.ReferenceRefer to location "AF - C3" on the schematic.
Illustration 2 g01379618
Place a jumper between pins "E", "F" and "Ground" on Connector B of the power module .
Measure the voltage between each of the following pins:
"A" and "B"
"C" and "D"
"G" and "H"Expected Result:The voltage that is measured between each set of contacts on the connector for the power module is machine voltage.Results:
YES - The voltage that is measured between each of the pins is machine voltage.Repair: Repair the wire harness or replace the wire harness.STOP
NO - The voltage that is measured between each of the pins is not machine voltage.Repair: Replace the power supply.STOP


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.