9V8946 LINES GP-COUPLER Caterpillar parts IT18 LINES
Rating:
Alternative (cross code) number:
CA9V8946
9V-8946
9V8946
CA9V8946
9V-8946
9V8946
Buy LINES GP-COUPLER 9V8946 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER,
Compatible equipment models: 9V8946:
INTEGRATED TOOLCARRIER IT18
Caterpillar
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1 Start By:
Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Remove" for the correct procedure. Note: Make a temporary mark on the components of the piston and connecting rod assembly. Making temporary marks will ensure that the components of each piston and connecting rod assembly can be reinstalled in the original cylinder. Mark the underside of the piston on the front pin boss. Do not interchange components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01341306
Illustration 2 g01341307
Remove bolts (12) and connecting rod cap (11) from connecting rod (6). Discard the bolts . Note: Fracture split connecting rods should not be left without the connecting rod caps installed. After the disassembly procedure for the piston and connecting rod is completed, carry out the assembly procedure and the installation procedure as soon as possible. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Assemble" and Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.
Remove lower bearing shell (10) from connecting rod cap (11). Remove upper bearing shell (9) from connecting rod (6). Keep the bearing shells together.
Place the piston and connecting rod assembly on a suitable surface with the connecting rod upward. Use Tooling (A) in order to remove circlips (5). Note: The forged Marks (X) may be on the front of the connecting rod assembly, or on the rear of the connecting rod assembly. The forged marks should not be used for the purposes of orientation.
Remove piston pin (7) and connecting rod (6) from piston (4). Note: If the piston pin cannot be removed by hand, heat the piston to a temperature of 45 5 °C (113 9 °F). Do not use a torch to heat the piston. Note the orientation of connecting rod (6) and piston (4).
Place the piston on a suitable surface with the crown upward. Use Tooling (B) in order to remove compression ring (1), and compression ring (2), and oil control ring (3) from piston (4). Note: Identify the position and orientation of compression ring (1), compression ring (2), and oil control ring (3).
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar dealer.
Inspect the connecting rod for wear or damage. If necessary, replace connecting rod (6) or replace the bush (8). Note: If the connecting rod or the bush for the piston pin are replaced, first identify the height grade of the connecting rod. Refer to Specifications, "Connecting Rods" for the correct information.
Repeat Step 1 through Step 6 in order to disassemble the remaining pistons and connecting rods.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1 Start By:
Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Remove" for the correct procedure. Note: Make a temporary mark on the components of the piston and connecting rod assembly. Making temporary marks will ensure that the components of each piston and connecting rod assembly can be reinstalled in the original cylinder. Mark the underside of the piston on the front pin boss. Do not interchange components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01341306
Illustration 2 g01341307
Remove bolts (12) and connecting rod cap (11) from connecting rod (6). Discard the bolts . Note: Fracture split connecting rods should not be left without the connecting rod caps installed. After the disassembly procedure for the piston and connecting rod is completed, carry out the assembly procedure and the installation procedure as soon as possible. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Assemble" and Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.
Remove lower bearing shell (10) from connecting rod cap (11). Remove upper bearing shell (9) from connecting rod (6). Keep the bearing shells together.
Place the piston and connecting rod assembly on a suitable surface with the connecting rod upward. Use Tooling (A) in order to remove circlips (5). Note: The forged Marks (X) may be on the front of the connecting rod assembly, or on the rear of the connecting rod assembly. The forged marks should not be used for the purposes of orientation.
Remove piston pin (7) and connecting rod (6) from piston (4). Note: If the piston pin cannot be removed by hand, heat the piston to a temperature of 45 5 °C (113 9 °F). Do not use a torch to heat the piston. Note the orientation of connecting rod (6) and piston (4).
Place the piston on a suitable surface with the crown upward. Use Tooling (B) in order to remove compression ring (1), and compression ring (2), and oil control ring (3) from piston (4). Note: Identify the position and orientation of compression ring (1), compression ring (2), and oil control ring (3).
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar dealer.
Inspect the connecting rod for wear or damage. If necessary, replace connecting rod (6) or replace the bush (8). Note: If the connecting rod or the bush for the piston pin are replaced, first identify the height grade of the connecting rod. Refer to Specifications, "Connecting Rods" for the correct information.
Repeat Step 1 through Step 6 in order to disassemble the remaining pistons and connecting rods.
Caterpillar SIS machinery equipment:
Caterpillar SIS
- 1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE » 9V-8946 LINES GP-COUPLER
- 1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE » 9V-8946 LINES GP-COUPLER
Parts lines Caterpillar catalog:
4W5025
LINES GP-ENGINE AIR
508, 916, 926, 926A, D3B, D3C, D4H, D4HTSK II, G916, G926, IT18, IT18B, IT28, IT28B
508, 916, 926, 926A, D3B, D3C, D4H, D4HTSK II, G916, G926, IT18, IT18B, IT28, IT28B
1W5867
LINES & FUEL FILTER GP
3204, 508, 916, 926, 926A, 943, 953, D3B, D3C, G916, G926, IT18, IT18B, IT28, IT28B
3204, 508, 916, 926, 926A, 943, 953, D3B, D3C, G916, G926, IT18, IT18B, IT28, IT28B
1W8869
LINES GP-TURBOCHARGER OIL
916, 926, 926A, G916, G926, IT18, IT18B, IT28, IT28B
916, 926, 926A, G916, G926, IT18, IT18B, IT28, IT28B
3V6298
LINES GP-TORQUE CONV COOLER
916, 926, 926A, G916, G926, IT18, IT18B, IT28, IT28B
916, 926, 926A, G916, G926, IT18, IT18B, IT28, IT28B
6W4855
LINES GP-AIR CONDITIONER
916, G916, G926, IT18, IT18B
916, G916, G926, IT18, IT18B
8V9304
LINES GP-STEERING
916, G916, IT18, IT18B
916, G916, IT18, IT18B
6W9722
LINES GP-FRONT
IT18, IT18B, IT28, IT28B
IT18, IT18B, IT28, IT28B
4N0188
LINES GP-WATER
215, 215B, 3204, 910, 916, 926, 926A, 931, 931B, 931C, 931C II, 935B, 935C, 935C II, 943, 953, D3, D3B, D3C, D3C II, D4B, D4C, D4C II, D4H, D4HTSK II, D5C, E180, G910, G916, G926, IT12, IT18, IT18B, I...
215, 215B, 3204, 910, 916, 926, 926A, 931, 931B, 931C, 931C II, 935B, 935C, 935C II, 943, 953, D3, D3B, D3C, D3C II, D4B, D4C, D4C II, D4H, D4HTSK II, D5C, E180, G910, G916, G926, IT12, IT18, IT18B, I...
9V3098
LINES GP-TILT CYLINDER
IT18, IT18B
IT18, IT18B
7G3056
LINES GP-POWER TRAIN OIL
916, G916, IT18, IT18B
916, G916, IT18, IT18B
3440632
LINES GP-AUXILIARY HYDRAULIC
305D CR, 305E
305D CR, 305E
2724411
LINES GP-PILOT
330D MH
330D MH
2807620
LINES GP-TRAVEL MOTOR
303.5C, 303.5D, 303.5E
303.5C, 303.5D, 303.5E
3455750
LINES GP-LIFT CYLINDER
242D, 257D, 259D
242D, 257D, 259D
2465950
LINES GP-WINCH
D6K, D6K LGP
D6K, D6K LGP
1G7751
LINES GP-HYDRAULIC
PM-565
PM-565
3912580
LINES GP-TILT CYLINDER
D6R STD
D6R STD
4196398
LINES GP-HYDRAULIC
621K, 623K, 623K LRC, 627K, 627K LRC
621K, 623K, 623K LRC, 627K, 627K LRC
1G5865
LINES GP-HYDRAULIC
PR-450C
PR-450C