AVSPARE.COM
parts catalog

LINK 1C4154 - Caterpillar



1C4154 LINK Caterpillar parts AP-1200 LINK
Rating:
15
Alternative (cross code) number:
CA1C4154
1C-4154
1C4154
Caterpillar 1C4154 LINK
Weight: 0.68 pounds 0 kg.

Buy LINK 1C4154 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT PAVER,

Compatible equipment models: 1C4154:

ASPHALT PAVER  AP-1200   Caterpillar
Number on catalog scheme: 9
 
  For full view, you need register

Information:

Removal Procedure
Failure to follow the instruction below for the installation of a work tool may result in personal injury or death. Special care must be taken if more than one person is installing the work tool.
Confirm the verbal communication and the hand signals that will be used during the installation.
Be alert for sudden movement of the front linkage and the work tool.
Do not insert fingers into the bores of the support pins when the support pins and the bores are being aligned.
To facilitate removal of the bucket pins without causing damage to the pins, the bearings, and/or the O-ring seals put the bucket on the floor and the stick in a vertical position, as shown.
Illustration 1 g06181120
Start the engine. Park the machine on a hard, level surface. Position the bucket, the stick, and the bucket control linkage, as shown. Shut off the engine.
Illustration 2 g06192508
Slide O-ring seals (1) off the pin joints and onto the flanges of the bucket.
When the pin assembly is removed, the linkage assembly may swing out of the bucket. To prevent possible personal injury, do not stand in front of the linkage assembly when the pin assembly is being removed.
Note: Removing the support pin may be difficult due to excessive pressure on the support pin. Remove the pressure on the support pin by adjusting the front linkage.
Illustration 3 g06186090
Remove nuts and retaining bolt (7) from support pin (2). Remove the support pin .
Remove bolts (3) and adapter plate (4). Remove the shims.
Remove nuts and retaining bolt (6) from support pin (5). Remove the support pin.
Start the engine and raise the stick out of the bucket.
Remove the O-ring seals (1) from the flanges on the bucket.Note: After the support pins have been removed, make sure that the support pins do not become contaminated with sand or dirt. Make sure that the seals on the end of the stick and the seals on the end of the link do not become damaged.Installation Procedure
Clean each pin and each pin bore. Lubricate each pin bore with molybdenum grease.
Illustration 4 g06192508
Position the O-ring seals (1) onto the flanges of the bucket.
Start the engine and lower the stick into the bucket until the pin bores are in alignment with each other. Stop the engine.
Illustration 5 g06186090
Install support pin (5). Align the retaining bolt hole in the support pin with the retaining bolt hole in the bucket.
Install the retaining bolt and nuts (6). Install adapter plate (4) without the shims, and without bolts (3) that hold the adapter plate.
Refer to Operation and Maintenance Manual, "Bucket Linkage - Inspect/Adjust" to adjust the bucket clearance.
Slide O-ring seals (1) in position over the pin joints between the

Caterpillar parts catalog:

Caterpillar parts catalog
AP-1200 ASPHALT PAVER 2JD00001-UP (MACHINE) POWERED BY 6.354 ENGINE


Parts link Caterpillar catalog:

3341154 LINK AS
320D, 320D FM, 320D FM RR, 324D FM, 324D FM LL, 325D FM, 330D FM, 568 FM LL
2543025 LINK & BEARING AS
324D, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D L, 329D, 329D L, 329D LN, 329E L, 329E LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E L, 336E LH, 336E LN, ...
2417150 LINK AS
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, ...
8C8186 LINK
AP-1200, AP-800
8C7763 LINK
AP-1200, AP-800
8C7835 LINK
AP-1200, AP-800
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.