AVSPARE.COM
parts catalog

LOUVER AR 1695445 - Caterpillar



1695445 LOUVER AR Caterpillar parts 3412, 3508, 3508B, 3512, 3512B, 3516, 3516B, PM3412 LOUVER
Rating:
41
Alternative (cross code) number:
CA1695445
169-5445
1695445
Caterpillar 1695445 LOUVER AR

Buy LOUVER AR 1695445 Caterpillar genuine, new aftermarket tractor parts with delivery
GEN SET ENGINE, POWER MODULE,

Compatible equipment models: 1695445:

GEN SET ENGINE  3412   3508   3508B   3512   3512B   3516   3516B  
POWER MODULE  PM3412   Caterpillar
  For full view, you need register

Information:

Probable Causes
Engine shutdown switches
Diagnostic codes and event codes
Batteries
Engine starting system
Flywheel ring gear
Driven equipment
Engine accessories
Hydraulic cylinder lock
Internal engine problem
Configuration parametersRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 1
Troubleshooting Test Steps Values Results
1. Check the Engine Shutdown Switches
A. The engine shutdown switches should be in the RUN position. Ensure that the shutdown switches are in the proper positions. Use Caterpillar Electronic Technician (ET) to verify the status of the "EMCP" and the "Remote E-Stop Switch" parameters.
B. When a shutdown occurs, the Electronic Control Module (ECM) must be powered down for at least 15 seconds prior to attempting to start the engine.
Shutdown Switches
Results: The shutdown switches are OK.
Repair: Proceed to the next Step
Results: The shutdown switch is NOT OK.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
2. Check the Batteries
A. Inspect the batteries.
B. Charge the batteries, if necessary. Refer to Special Instruction, SEHS7633, "Battery Test Procedure".
C. Load test the batteries. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 V and 12 V Lead Acid Batteries"
Batteries
Results: The batteries are OK.
Repair: Proceed to the next Step
Results: The batteries are NOT OK.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
3. Check the Electric Starting System (if applicable)
A. If the application is equipped with an electric starting system, perform the following procedure:
a. Check the wiring to the starting motor solenoid. Refer to the electrical schematic.
b. Check the engine start switch and the engine start relay for electrical power.
c. Check the starting motor cables. If the starting motor cables are corroded, remove the starting motor cables and clean the starting motor cables.
d. Test the operation of the starting motors.
Starter
Results: The electric starter is OK.
Repair: Proceed to Test Step 7
Proceed to Test Step
Results: The electric starter is NOT OK.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
4. Check the Air Starting System (if applicable)
A. If the application is equipped with an air start system, perform the following procedure:
a. Verify that the air start system has an adequate supply pressure for starting.
b. Check the wiring to the air start relay that is for the air starting motors. Refer

Caterpillar SIS machinery equipment:

Caterpillar SIS


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.