AVSPARE.COM
parts catalog

MAGNET 4645033 - Caterpillar



4645033 MAGNET Caterpillar parts MAGNET
Rating:
36
Alternative (cross code) number:
CA4645033
464-5033
4645033
Caterpillar 4645033 MAGNET
Weight: 0.28 pounds 0 kg.

Buy MAGNET 4645033 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 4
 
  For full view, you need register

Information:


Remove gray cap (K) and release the connector pins using appropriate tool from connector (J).
Illustration 9 g06335811
(J) Connector
Illustration 10 g06215298
Front side of operator console showing the back side of removed display
(J) Connector
Illustration 11 g06215270
Connector configuration table
Terminate 535-6932 Cable As (1) by plugging in the black wires in either position 3 or position 6 of the connector (J).Note: Unplug the connector from the display as shown in Illustration 9 and tie it back, as it will no longer be used.Note: Plug the new USB harness to the connector on the display as shown in Illustration 10.
Illustration 12 g06215368
(3) 535-6992 Plate
Locate plate (3) with respect to the dimensions indicated in Figure 12.
Illustration 13 g06215336
(3) 535-6992 Plate
Using plate (3) as a template, mark and drill three holes with reference to the specification given in Figure 13. Before drilling, precautions to be taken not to contact the harness.
Illustration 14 g06215378
(3) 535-6992 Plate
(4) 9X-2041 Screw
(5) 344-5675 Nut
(6) 8T-4121 Hard Washer
Place plate (3) to match the position of the drilled holes with the holes on the plate. Install the plate using two screws (4), two nuts (5), and two hard washers (6).
Illustration 15 g06215401
(1) 535-6932 Cable As
(7) 7K-1181 Cable Strap
(L) Harness
Route the cable assembly (1) along existing harness (L) using five cable straps (7).Attach USB cable port end to 535-6992 Plate (3) previously installed.
Illustration 16 g06215411
(3) 535-6992 Plate
(8) 535-6869 Film
Install film (8) on plate (3) by positioning the film as shown in Figure 16.
Illustration 17 g06215414
(M) Location of existing USB port
Remove the existing 398-3073 USB Cable As from location (M) on center machine console. Leave the machine side harness attached to existing retaining clip.The 344-7618 Seal Cover from existing USB port can now be installed on the new USB port location by attaching the tether of the seal cover to the new USB port location.
Illustration 18 g06216808
(9) 7X-1442 Button Plug
Install plug (9) on the location from where the existing USB port was removed.
Illustration 19 g06223212
View of USB port in new location after the rework
(3) 535-6992 Plate
Install all covers and plates removed and saved in Step 1 to Step 5.

Caterpillar parts catalog:

Caterpillar parts catalog
AP255E Asphalt Paver D8A00001-UP (MACHINE) POWERED BY C2.2 Engine


Parts magnet Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.